Small Conveyor Belt Systems

Hot Products

Belt Conveyor Troughing Idler Frames

Belt Conveyor

Rubber Coating Conveyor Roller

Belt Conveyor CEMA Idler Sets and Idler Group

Belt Conveyor Troughing Idlers

Gravity Roller Conveyor, PVC Roller

Solpe (Incline) Belt conveyor

Gavity Roller Conveyor

Solpe (Incline) Belt Conveyor

Conveyor Belt Rubber Roller

FAQ

Hello, I would like to consult the power between the conveyor and the motor is the same Mody, is not the conversion of the formula is what ah, thank you

Is the motor does not transfer the conveyor belt can do work

My automatic mahjong table conveyor belt how to reverse the motor, it should be up to send the card, and now it will pass down the card, resulting in the card simply do not get on, the magnetic circles suck the cards are gone, Do not say anything more

Have you ever been repaired? According to what you said, I made a look at the analysis, please refer to: First, as the first floor said, continued electrical (capacitor) is broken, you can change a high-power, but the motor will have some sound, can barely use. Or directly replace the motor Second, the conveyor belt dirty, mahjong table conveyor belt motor with a reverse function, if the belt is dirty, forward belt does not move, it leads to reverse. You can spray Billy beads on top of the belt to try, it is best to wash mahjong. Third, the motherboard is broken, it is more complex, motherboard circuit problems, according to the brand you buy, find manufacturers to replace the general warranty. Fourth, K4 light sensor for, resulting in not read the card, paint about the light, that is, on the licensing device, there are two small bulb-style stuff. You can also adjust its sensitivity to try. Fifth, the mahjong table this stuff, fear of tide, pay attention to keep dry. Sixth, if the above method no longer, mahjong table with automatic detection file, you can adjust to the detection file, automatic detection, according to the instructions. If not, it is best to find a professional. This is my personal point of maintenance experience, hoping to help you. for reference only.

What is the motor used in the pipeline in the factory? Above also equipped with a reducer, you can adjust the speed of the motor, this motor is what motor? What is the general model? How can we buy the right motor? I do not know what type of motor to buy ////////////////////////////////// more

Not seen but can refer to the three-phase asynchronous motor, in order to facilitate speed adjustment, the use of inverter frequency control motor speed, if you do not need speed control occasions, the ordinary three-phase asynchronous motor on it.

What is the motor in the conveyor belt (pipelined) The kind of motor also has a speed control box, but not the inverter.

You use this governor to use a governor control, commonly used in low-power motor, 400W below the use of common 200W following motor, speed control panel + motor cost is low, more than 400W using the inverter control, the motor is asynchronous motor, There are two phases and three phases.

How to weld the belt on the belt conveyor belt broken, and how to get the most reliable?

Manufacturers have a special tool ... two electric mold a total of two, first of all to the broken belt to deal with both ends, and then power electric heating mold, the belt on the middle of two molds, heating ... ... not too long, half Hours on ok

The motor has a fixed diameter wheel, connecting the conveyor belt. Conveyor belt with a large round of walking slow, or with a little bit of the wheel to go slow?

The speed of the conveyor belt is determined by the speed of the wheels and the motor on the motor

To design a conveyor belt, 2 m / min, 3 m long, used to send the PCB board, very light, that is, do not know the choice of the motor, what about the power, and the wheel is not casually size, , The motor to add the inverter, or gear motor, or electronic regulator? Which is more suitable, why? Can you tell me Do not copy some online have to perfunctory! Thank you! More

Speed belt belt / drive the best, the roller can be added 3 ¤ 10mm (short), the electronic governor has not been able to tune 3 phase, 1.5KW motor is enough, of course, but also control the electrical leakage, Open,

I have two sets of conveyor belt, cylinder and air compressor, the trachea are connected. The existing JS14P time relay 1, CJX2-1210 contactor 2, are AC220V, diffuse photoelectric switch 1 [2 lines often open 220V], how to wiring? Puzzled line of their own, but there is a contactor will be baffled, how to solve, how to properly wiring. Urgent thanks! Question added: I would like to ask which master can draw a picture really thank the younger brother

I remember the sensor can be connected to the back of the electrical