Ferro Phosphorus

Hot Products

FeMn Good Quality Low Carbon

Ferroalloy Type Ferrosilicon FeSi 72%

Ferro Alloy L.C.FeCr Metal Powder Price

Nitrided Ferro Chrome, LC FeCr

RE FeSi For Casting Manufactural

Good Fesi As Inoculant

Metal Manufacturer Medium Carbon FeMn

FeMn Low Carbon Manganese

FeSi 75 - 65 # With Hight Quality And Low Price

High Carbon Femn For Steelmaking

FAQ

What are the parameters of the wear resistance of cemented carbides in addition to their hardness?

Even the best knives in the world, if not1, reasonable processing parameters;2 、 proper installation and use;3 、 timely maintenanceAnd so on, it will turn into a scrap of iron in a short time.

The difference between cemented carbide YG 15 and yg12

Material introduction: YG3X 14.6-15.2 132092 is suitable for high speed finish machining of cast iron, non-ferrous metal and alloy, hardened steel, alloy steel and small cutting section. K01 YG3X YG6A 14.6-15.0 137091.5 is suitable for semi hard finishing of hard cast iron, non-ferrous metals and their alloys. It is also suitable for semi finishing and finishing of high manganese steel, quenched steel and alloy steel. K05 YG6A YG6X 14.6-15.0 142091 has been proved by the production and use that the alloy can be used to process chilled alloy cast iron and heat-resisting alloy steel. It can also achieve good results and is also suitable for the finishing of ordinary cast iron. K10 YG6X YK15 14.2-14.6 210091 is suitable for processing integral alloy drilling, milling, reaming and other cutting tools. It has high wear resistance and toughness. K15 K20 YK15 YG6 14.5-14.9 138089 is suitable for semi finishing with medium casting speed of cast iron, non-ferrous metals and alloys, non-metallic materials. K20 YG6 YG6X-1 14.6-15.0 150090 is suitable for cast iron, nonferrous metals and alloy non metal material during continuous cutting finishing, discontinuous cutting the semi refined car, fine car, small section fine car, coarse thread, continuous section semi finishing milling and finish milling, rough and fine hole expansion. K20 YG6X-1 YG8N 14.5-14.8 200090 is suitable for high speed cutting of cast iron, white cast iron, nodular cast iron, and chrome, nickel and stainless steel.

What cemented carbide does 2gr13 use?

2Cr13 martensitic stainless steel can be processed by hard alloy YW2, carbide YW2 suitable for heat-resistant steel, high manganese steel, stainless steel and advanced alloy steel and other special difficult to processing steel finishing, semi finishing.

Are there any German products called K44 which are imported into cemented carbide materials? I am machining hole, K44 is better than domestic material K30?

Germany never heard of K44, I know K40 is the international organization for standardization as the equivalent of the national standard YG-10H, the hardness of about 1300HV, used for processing softwood or hardwood and nonferrous metal; K30 is equivalent to the national standard YG-8, the hardness of about 1400HV, suitable for low hardness of grey cast iron, low tensile strength steel and compressed wood.Compared with the two, K40 has higher toughness, but its wear resistance is lower.

Where does Tianjin sell yt30 carbide tool?

Now there are the same, express, everything is not afraid. I am the agent of Zigong the Great Wall brand cemented carbide, quality assurance, definitely authentic.

What is the relation between the number of teeth of carbide saw blades?

Hard alloy tooth less than wood section tooth more smooth, less than the price of gear teeth is cheap, less than the number of gear teeth is not easy to burn saw, if multiple saw tooth must use less, if it is a plywood class, must use the teeth reduce edge collapse.

What are the standard units of measurement for carbide inserts?

Manufacturers usually use KG, which is used inside the shop

What materials are ZK20 cemented carbides processed?

ZK20 belongs to the K hard alloy blades can car many materials, such as: wrought iron steel low alloy cast iron high alloy cast iron ductile cast iron Aluminum Alloy hard plastic