Silver Plating Copper Wire Silver Magnet Wire

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Packaging Detail:	silver plating copper wire by Plastic bobbin+Carton+Pallet
Delivery Detail:	silver plating copper wire will be shipped within 15 days

silver plating copper wire silver magnet wire
Size: 0.02mm~2.60mm
Month Capacity: 10 tons
Material:99.99% silver & 99.99% cu

Product Description

silver plating copper wire silver magnet wire

Standard:

JB/T 3135-2011 Silver coated annealed round copper wire .

ASTM B298-12 Standard Specification for Silver-Coated Soft or Annealed Copper Wire .

Advantages :

Scope of Supply of silver coated round copper wire: 0.02-2.60mm

Product Types

TRY A, SILVER VOLUME IN WEIGHT 1.25%;
TRY B, SILVER VOLUME IN WEIGHT 2.50%;
TRY C, SILVER VOLUME IN WEIGHT 4.00%;
TRY D, SILVER VOLUME IN WEIGHT 6.00%;
TRY E, SILVER VOLUME IN WEIGHT 10.00%;
SILVER PLATED THICKNESS ACCORDING TO JB/T 3135-2011 ITEM 4.2.1 OR ASTM B298 TABLE 1.

Q: Ceiling fan has a black wire, white wire, green wire and also a black and white wire.: The white wire from the fan gets connected to the white wire (neutral) in the ceiling box. The green wire is ground. It is connected to the fan mounting bar where the bare copper wire is connected. The remaining two wires are your hot wires. One goes to the fan and the other goes to the lights so you can run the lights on a dimmer circuit. I believe the black is for the fan and the black-white is for the lights. Your fan's instruction manual should identify these wires. IMPORTANT: Never run the fan motor on a standard dimmer. A dimmer is designed for use with resistive loads like incandescent, halogen, and (to some degree) LED lamps only. Running an inductive load like a fan motor will create noise spikes on your electrical circuit and possibly overheat the motor causing premature failure.

Q: Does anybody know where on the internet i can find the radio wiring diagrams of a factory radio???: Put a V8 in that bad boy! J/K sorry. Sounds like maybe an ignition coil, plug wire loose or bad or possibly an injector like the last guy said.

Q: I need to get to the audio wiring: you cannot simply go with matching the colors factory radios have extra wires that are not needed with an aftermarket install most of the time (wires that control the dimmer on the radio, speed sensitive volume) you will need three power wires (constant, ignition, and ground), plus your speaker wires use a test light to test your wires, usually at the radio the yellow wire is your constant, the red is your ignition, and black is always ground to find your constant use the test light, it will be hot at all times so that your radio can remember the time, and your settings- next you need your ignition, it is only hot when the key is on or in the accessory position, to tell the radio when to come on- the ground is self explanatory to find which wires go to what speakers all you need is a 9v battery, put the positive end to a wire and test all of the other wires to the negative side and you will hear a crackling noise from a speaker when you have the right combination

Q: On a seat switch on a poulan mower it has three wires are two of them grounds or one.: It's probably one positive, one negative and one earth ground.

Q: I need to rewire my boats trolling motor wiring.. I have a 55# thrust trolling motor witch draws about 45-50 amps under a full load. I have 8 GA on hand I could use.. but would I get full power out of my motor? Does 8 gauge wire support 50 amps? It is stereo wire.. Braided copper wiring.: How long is the wire run? 8-gauge can handle 50 amps safely, but you may get an unacceptable level of voltage drop if the wire run is very long. If it's just a few feet, it should be fine. If you have enough wire, you can always use two runs. If you combine two 8-gauge wires, it's the equivalent of a 5-gauge wire.

Q: for california electrical code, am i limited to insert no more than one wire per knockout on a box ?: no. the number of wires in the box is restricted based on the volume of the box but the number of wires entering a knock out is restricted by the size of the conduit or the cable type connected to the knock out.

Q: does anyone have a wiring diagram for a rccb or can you explain how to wire one up . as an rcd has a wiring for connecting to earth but an rccb does not have that.: RCCB is Resual Current Circuit breaker, so it operates sensing the difference in voltage in the phases and neutral... ie if an earth leakage is occured there will be a difference in the current flowing through and hence activating the trip ckt if the RCCB and causing trip. Thus the earth connection is not required for the rccb.. so go ahead without the earth wire...

Q: do i need a wiring harness or can i use wire crimps and do it w.o on a 2000 blazer 4wd if u think i need it plz tell me thanks: unless you known what each wire does get the wiring harness or you very well may destroy your head unit

Q: Why is thin strand wire better for powering car audio?: Thin strand wire is more flexible and so stands up to the flexing and vibration in a car application better. May not be an issue in the short term, but over time the thinner strand should hold up better

Q: I need to buy some electrical wire for my car, does it matter what color the copper wire is inside of ( i.e. black,yellow,red,green,blue,etc.): The color of the wire indicates wire gage

Send your message to us

*Email

*TEL

*Quantity

*Unit