SAP Single-stage double-suction centrifugal pumps
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Type SAP is researched and developed on the basis of type SA and absorbed the advanced technology of domestic and foreign similar products
Performance range: Capacity: 72--9900 m3/h
Head: 6.8_104m
All the data of pumps can be changed according to requirements of clients.
Construction: The pump is horizontally installed. The inlet and outlet are under the split surface and in the perpendicular direction with pump central shaft-line, during the course during the course of installation, you needn't to remove the motor and the pipes.
Type SLA is vertically installed the inlet and outlet at a same center line and the case and cover are in the perpendicular direction.
Bearing: Both end of the pump are rolling bearings (type 24SA_18, 16SA_90 could use the sleeve bearings)to support the rotor, the lubrication oil is dilute oil or grease.
Materials of tolerance: The material s of tolerance is cast iron or it can be changed into cast steel and bronze, but it should be signed in the order.
If you have any special requirement, please contact us without hesitation.
- Q: Know flow and lift how to calculate the pump power?
- N=Q.H.g. P / nN - motor power, kWH - pump head, MQ - pump flow, m^3/sG - gravity acceleration g=9.81
- Q: What does the pump mortar do?
- 1: 2 cement mortar or cement mortar with the same proportion of other components except coarse aggregate in the concrete, the pump piston and the inner wall of the pipeline are fully lubricated, and a layer of lubricating film is formed
- Q: The difference between diaphragm pumps, vacuum pumps and centrifugal pumps
- The diaphragm works by changing the size of the diaphragm. When the cup is covered with an eraser and the edge is airtight, then pressing the rubber or pulling the rubber outward will make the pressure in the cup increase or decrease. Use this principle, in the pressure of an hour from a hole suction medium, when the pressure is large, from another hole extrusion medium, so as to achieve the purpose of conveying.
- Q: Double floor sewage pump circuit diagram of a small problem
- Question 4 when you need backup, you need to switch the SA switch, but where you want it. For example, when the 1# pump is running and does not reach the high water level, the 2# pump will not operate. If SA is placed in the left position, 21 and 22 are connected, and the KT is electrically delayed, and the KAB action causes the 2# pump to function. After the KAB operation, the KT will be disconnected, restored to the ready state, and also convenient for KT to restart the power on time, and also avoid the time relay to work on a long-term basis.
- Q: Is the sewage pump the same as the mud pump?
- The upstream return speed of the washing fluid is required to remove the cuttings and rock powder from the drill in a timely manner from the bottom of the hole and reliably carry it to the surface. Through drilling and extraction, mud can be obtained at the bottom.
- Q: What is the main difference between SK water ring vacuum pump and 2BV water ring vacuum pump?
- SK vacuum pump is a single-stage water ring vacuum pump, vacuum pump and motor separation, coupled with couplings, vacuum relatively low.
- Q: Working principle and structure of external gear pump
- The principle of the gear pump, gear pump structure consists of two gear mesh together with each other, and composed of pumps known as gear pumps. It relies on the gear teeth meshing space change in volume to transport the liquid, it belongs to the rotary pump, also can be considered as a volume pump. There are many kinds of gear pumps. According to the meshing mode, it can be divided into external gear pump and internal gear pump. According to the tooth shape of gear, it can be divided into positive gear pump, helical gear pump and herringbone gear pump.
- Q: Water pump spoon pipe for power plantWhich hero can tell me what is the water pump spoon tube ah? And its role
- By adjusting the amount of oil entering into the hydraulic coupler, the torque of the hydraulic coupler can be controlled
- Q: What's the difference between a centrifugal pump and a centrifugal pump? What are they used for?
- Centrifugal pumps are used to transport liquids (or mixtures, waste water, waste materials) from one location to another.
- Q: What is the difference between an air pump and a water pump?
- A pump is a machine that transports liquids or pumps liquids. It will be the prime mover of the mechanical energy or other external energy transfer to the liquid, the liquid energy increase, mainly used to transport liquids including water, oil, alkali liquid, emulsion, suspension emulsion and liquid metal, but also transport liquid, gas mixtures and liquids containing suspended solids.
Send your message to us
SAP Single-stage double-suction centrifugal pumps
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
