Long Working Life and Good Material 5' Metal Forged Grinding Steel Ball for Sag Mill
- Ref Price:
-
- Loading Port:
- Shanghai Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25M.T. m.t.
- Supply Capability:
- 200000M.T./Year m.t./month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Good Quality of Long Working Life and Good Material 5' Metal Forged Grinding Steel Ball for Sag Mill
HRC45-65 and no breakage, In normal use process, if the broken rate is high, we will be free for you in the new product and compensate for your losses .
Full Sevice of Long Working Life and Good Material 5' Metal Forged Grinding Steel Ball for Sag Mill
From you send me inquiry until you using the products, if there is any question, you can contact me at any time, my telephone will be opened for you in 24 hours.
Chemical Composition of Long Working Life and Good Material 5' Metal Forged Grinding Steel Ball for Sag Mill
C | Mn | Si | Cr | Mo | S | P | |||||
Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Max | Max |
0.52 | 0.85 | 0.60 | 1.10 | 0.17 | 0.37 | 0.05 | 0.25 | 0.00 | 0.04 | 0.04 | 0.035 |
Hardness of Long Working Life and Good Material 5' Metal Forged Grinding Steel Ball for Sag Mill
DIA25MM-DIA110MM | DIA125MM-DIA150MM | |
Superficial | 55HRC-65HRC | 53HRC-63HRC |
Volumetric | 55HRC-65HRC | 53HRC-63HRC |
- Q:What are the general technical requirements for casting parts?
- Satisfy appearance quality (appearance defect, quality change, size deviation)Intrinsic quality (composition, properties, internal organization)Service performance (abrasion resistance, corrosion resistance, heat resistance, pressure resistance)
- Q:What are the causes of pitting on the surface of a precision casting?
- There is a bump on the mold. Or casting cooling fast.
- Q:How can the casting be free of trachoma?
- 2, pouring temperature should be enough, otherwise the sand can not float up;
- Q:What are the casting parts tested?
- The surface brightness, appearance, size, chemical composition, weight, material, surface defects, internal defects, seals need to be checked, leakage, etc.
- Q:How do you mark it on the drawing? Do you need to discuss it with the manufacturer?Because the casting allowance is the standard, then, after all, is the theoretical value, the actual level depends on the manufacturer, so is it necessary to ask the manufacturer?
- The general foundry casting technology division will mark put shrinkage and the allowance of the map in your chart (usually with the red pen) for the production of wood or other material wood workers die drawings.
- Q:the parts of the threaded hole is casting, casting the hole directly, and then tapping or casting, and then punch 10When the casting is ready, punch it again before tapping it Is the hole casting good or is it punched and tapped on the drilling machine after casting?
- There are several casesThe first hole with a diameter of less than 4MM is generally not done, or as a hole location only for a period of less than 10MM.Second for the big hole, some of the reasons for the holding force, we must increase the slope, direct tapping is unlikely, so it still needs post-processingThird for products with high tightness requirements, some cores need to be made even if they are very small, so they can be tapped directlyFourth, some due to technical requirements, regardless of the size of each other's requirements must be made, there is no wayThe above methods are common, and they will encounter many small problems in actual production.
- Q:What is the difference between casting and stamping parts?
- The purpose of forming processes is to allow the sheet to undergo plastic deformation without breaking the billet and to make the desired shape and size. In actual production, a variety of processes are often applied to a workpiece. Blanking, bending, shearing, drawing, bulging, spinning and rectification are several main stamping processes. The difference between stamping parts and castings: with thin, uniform, light, strong features, stamping can be produced by other methods difficult to make, with stiffeners, ribs, UPS or flanging of the workpiece, to improve its rigidity. Due to the use of precision molds, the workpiece accuracy up to microns, and repeated high precision, specifications consistent, you can punch out of the hole, lug and so on.
- Q:Selection of hydraulic press is the casting parts and steel plate welding, how to choose?
- Casting parts in one shape, the overall processing in this regard than steel plate welding better. The same price is much more expensive than steel. Large hydraulic presses seldom have casting parts.
- Q:Lathe processing stainless steel casting parts to use what type of tool, the speed into the amount of how much tool angle
- There is YW1 best, if not using YG6X, YG8 is ok!The speed should not be high, the greater the diameter, the lower the speed! For example, a diameter of 100 mm, speed is not greater than 80 rpm, each point is good!The main tool is the front angle to be larger, more than 6 degrees, and the groove should be wider and larger to reduce the cutting resistance! When the rear angle is properly reduced and the strength is increased, it is recommended to take 3 degrees.The main components are: spindle box, exchange gear box, feed box, slide box, tool post, tail frame, light bar, lead screw, bed, foot and cooling device.Spindle box: also known as the headstock, it is the main task of the rotary motion of the main motor came through the transmission mechanism of a series of positive and negative spindle to be required two different steering speed, the spindle box gives impetus to the movement of the box. Medium spindle is the key part of lathe. The stability of the spindle on the bearing directly affects the quality of the workpiece. Once the rotation accuracy of the main shaft is reduced, the value of the machine tool will be lowered.
- Q:Which surface is coarser for cast iron or cast steel castings? Why?
- Roughness mainly depends on the surface roughness on the surface of the sand.
Grinding Prince was established in February, 2004 with an area of 24,400 square meters. Our company is an outstanding private enterprise specializing in the production of wear-resistant, corrosion-resistant, and heat-resistant alloy iron and steel castings. Currently, our production capacity of various types of wear-resistant casting balls and heat-resistant steel castings is 10,000 tons.
1. Manufacturer Overview |
|
|---|---|
| Location | Anshan City, Liaoning Province,China |
| Year Established | 2002 |
| Annual Output Value | US$1 Million - US$2.5 Million |
| Main Markets | Domestic Market； South America； Eastern Asia； South Asia； Mid East |
| Company Certifications | ISO9001;IS014001 Certificate |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | Shanghai Port;Dalian Port;Tianjin Port;Yingkou Port |
| Export Percentage | |
| No.of Employees in Trade Department | 6 - 10 People |
| Language Spoken: | English; Chinese; Spanish |
| b)Factory Information | |
| Factory Size: | 24,400 square meters |
| No. of Production Lines | Above 10 |
| Contract Manufacturing | grinding ball,grinding media,casting ball,casting grinding ball |
| Product Price Range | Average |
Send your message to us
Long Working Life and Good Material 5' Metal Forged Grinding Steel Ball for Sag Mill
- Ref Price:
-
- Loading Port:
- Shanghai Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25M.T. m.t.
- Supply Capability:
- 200000M.T./Year m.t./month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
New products
Hot products
Hot Searches
Related keywords
