knife seat，F-KB053 acacia wood magnetic knife seat
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
MEAS：22*24*4cm
Key Specifications/Special Features:
Size can be customized
Can print your design of packing
Various styles for choice
Can print your design of packing
Small quantity order is accepted
We also have bamboo and plastic cutting board for choice
Our advantages:
All of our products are made by our experienced team of hard working artisans in a safe and responsible environment.
We take great pride not only in the outstanding quality of our products but also in the environment in which they are made
Every product that bears our name was made in an ethically and socially responsible way
Treated by high temperature, making our product antibacterial
Easy to clean, much durable and harder than other board due to the good material
Primary Competitive Advantages:
Brand-name Parts Country of Origin
Distributorships Offered Experienced Staff
Form A Green Product
Guarantee/Warranty International Approvals
Packaging Price
Product Features Product Performance
Prompt Delivery
- Q: The system is a wide number of 980TDb, lathe is the Yunnan machine tool factory. Whether it is a manual tool change or MDI way to enter the specified number of knives, the tool holder always turn around, until the emergence of PLC alarm 1000 change knife time is too long, A0000.0 knife can not reach the designated position. What the problem ah, I did not move the parameters of the machine, ah, this morning is good, work in the afternoon a boot on this.Back to the origin of the machine are abnormal, and can not return to the origin of the machine. Press the corresponding button after the machine does not respond, will not act. It's normal in the morning.
- Note: it is important to ensure the lubrication system
- Q: How can we remove the NC turret
- The first part of the rotation, two screws in the middle of the release, and then lock the 12 release of the knife rest, remember there are still under the four, in the middle of the road there is a flexible adjustment of the long screws
- Q: How to do the slide shoe
- Nails can be used as follows.Use a hammer to hammer the bigger one in the mouth, then screw it.In addition, there is a special tool for dealing with sliding wire. You can break a nail.Knife slide wire no way, can only change the tool holder. Even if the wire tapping to do the thread, the diameter is not the same as the original
- Q: Tool holder S solution
- Modified DIY it certainly is h good, can change the surface of bamboo wood aluminum can, spray painting stickers can... The support of the s arm than the low end of the non uniform force... The actual s arm didn't what reinforced technology, the most vulnerable to bad is that even if you part of aluminum, steel shaft intact, aluminum bent??? From the point of view of the wheel easy disassembly, s frame is much better, less two outer shaft on the convenience. As for the slide is more dependent on the wheels and bearings, s frame is close to the center of gravity of the Double Tour dragon board, h's center of gravity close to the long plate in the skateboard, of course, the difference is not so big, more difficult than the long board.
- Q: However, No. 2, No. 3, the normal use of potential energy on the knife No. 4 can not be normal use of the rotation has not stopped on the 1.
- There is a problem with line 4, the signal is not detected
- Q: What is the tool rest
- The tool holder is arranged in order to prevent the workpiece from being bent and deformed when the workpiece is cut by the cutter, so that the diameter of the part is larger. Is in the process of moving together with the head.
- Q: The direction of the tool head and the tool head of the NC lathe
- G41g42 use the judgment of the tool tip is not the same as you this figure to 09 knife point for the center of the rotation of 180 degrees is the rear tool head position input value evaluation standard front and rear is the same as the input value
- Q: GSK980TA CNC lathe tool holder how to move
- Behind three with the line for a try, if the impact of the knife should be a pin problem, open the adjustment OK
- Q: The rotary tool holder is marked with the knife number. How to define the knife number?
- There is no knife in the actual sense of the knife number, because it is to use the knife to determine the use of the.
- Q: The difference between the turret and the rear turret NC lathe
- No big difference, mainly to see the design of machine tool manufacturers have their own customized. Such as the electric knife in front of their own called the front tool holder, with the opposite of the rear cutter. There is also a row of knives, in the car arc, the knife installed on the back of the knife, the programming instructions to be divided into circular arc, arc
Send your message to us
knife seat，F-KB053 acacia wood magnetic knife seat
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
