knife seat,F-KB023 beech knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
product name：rubber wood knife seat
material：rubber wood
MEAS：31*22.8cm
Specifications:
Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense
Excellent toughness, process into various curved according to the needs , full of beauty
Solid texture，manufactured goods with firm structure，prolonged service life
The texture of rubber wood is fine and closely woven，pore full of lots ot padding so it's hard to absorb water and corrode.
Description：
1、The knife seat use material of high quality natural rubber wood and take professional advanced machine equipment and manual binding.
2、The knife seat was refined by material, assembly, polishing, painting and other procedures.
3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.
4、Hoteam commerce co.，LTD，is a manufactory specialized in all kinds of wood knife handles，wood seats，chopping boards and other woodworks.
5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure that dry and clean and put
it in the open air
- Q: The cutting surface of the optical fiber cutter is like this, what's going on?
- The blade is high, it is recommended to turn down a little.
- Q: Drilling out of the hole is the overall deviation, the hole is 0.15, the cutting tool angle is not biased, the product is not how to jump, I was the first drilling after the chamfer, is how to go wrong, in this case, ask the teacher, thank you first, urgent...
- The overall mean partial is specific bit big?1 first check the bottom of the hole with the size of the hole is the same if it can not be determined for the drill bit tilted2 drill bit size is not accurate in general has a few wire error is normalIf you are talking about the normal eccentricity the central axis of the hole is not a shaft with the central axis of the workpieceSo it is the problem of the chuck first clean the chuck jaws necessary when the car can claw a knife and then try to solve the problemIf not, that's the problem with the chuck assembly
- Q: The difference between the center and the rest
- The 1 center frame is fixed on the bed rail, and has three independently movable supporting claws, and can be fixed by fastening screws. When in use, the workpiece is arranged on the front and rear top, in the first part of a workpiece support finishing smooth surface, then the proper position of center frame fastened to the guide rail, the final adjustment of three supporting claws, make contact with the workpiece supporting surface, and adjust to the proper degree of tightness.
- Q: What is the difference between the KSJ and HV
- The basic difference is that logo is different!! Others say the KSJ shelf is better than HV! But I think there's no difference!
- Q: How to maintain the lathe tool holder
- If the positioning and clamping action is normal, the push rod 11 is in contact with the corresponding contact 12, and the signal is sent to indicate that the tool changing process has ended, and the cutting process can be carried out.In addition to the positioning of the hydraulic cylinder and the positioning pin, the motor can also be used to drive the clutch to locate, as well as other indexing and positioning mechanisms.
- Q: The development trend of numerical control tool holder
- Vertical tool holder has four, six stations in the form of two, mainly for simple CNC lathe; horizontal tool holder has a position of eight, ten, twelve, can be positive and opposite direction rotation, the nearest election knife for the full function CNC lathe. In addition, the horizontal tool holder is provided with a hydraulic tool holder and a servo driving tool holder.
- Q: What are the parts of the lathe and tool holder
- A lathe is a device; a tool holder is a lathe.
- Q: 1, CNC horizontal lathe tool holder with front and rear respectively. CNC vertical lathe tool holder how to classify?2, no matter front or rear CNC lathe, cutter movement from right to left (along the Z axis) with G42 compensation?
- In the tip of the compensation bar to enter the radius of the tip of the knife is good, of course, we must first know the radius of the tip of the nose,
- Q: How to return to the ordinary lathe tool
- Remove and check whether the spring pin back position is smooth (with the hands of the press about 20 times). Take a look at whether the end of the spring pin has been seriously worn, the same knife bottom surface is also turned over to see if the limit groove is also serious wear.
- Q: CNC machine tool can be drilled hole how to center
- 1, do not need to set the coordinate system (the center), is loaded with a knife, in the process of preparation of processing requirements, reasonable adjust the height and verticality, the proper use of speed and feed rate, the knife tool can be set, simple, can fix a hole.2, if the degree of difficulty and high requirements, please use the circular drilling instructions programming.
Send your message to us
knife seat,F-KB023 beech knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
