Hot Selling Glazed Porcelain Tiles

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

specifictions

• 1. various sizes are available;

• 2. More than 100 design andcolors;

• 3. Both waterproof and nonwaterproof available;

• 4. Strict control on colortolerance;

• 5. Perfect effect on flatness andglazed surface;

• 6. Ink-Jet technology applicationon the tiles

• 7. Stable production andsupplying;

• 8. Competitive price and paymentterm

• 9. Stable production andsupplying;

• 10. Suitable for economic endusing;

Q: my tiles i am using are 13 inch,and i am doing a 4x8 wall,so i was wondering which is the best way to adhere it: Best Tile Adhesive

Q: How does the tile stick up? The benefits of stickers? What is the difference between sticky and wet stickers? Do i want to be thin: Want to thin point will wall flatness is good, the actual tile adhesive layer is less than 1cm; most of the thickness of the leveling layer, the general construction plaster 2 m error of about 1-1.5cm, then the actual paste tile gray The thickness of the need to reach 2-2.5cm, and then thin can not be friends, or paste in the glass is very flat on the basis of

Q: Do you have, or know someone who has these tiles in the bathroom? What is their experience?: Modern stick on tiles work well with occasional dampness. I've got them in my mud room and I installed them in a friend's mud room as well. They've held up perfectly for years. The issue you're more likely to have problems with is with the subfloor. If water can get between the tiles it will be absorbed by most subfloors. Once it's in there it has a hard time evaporating out since the tiles cover the surface. An easy way to avoid this problem is to coat the subfloor with a couple layers of polyurethane before applying the tiles. Just sweep and vacuum the floor to get it nice and clean, then brush on a coat. You don't need to make it perfect or anything, you're just creating a water barrier. Once that one dries apply one more coat, let it dry, wipe the entire surface down with 220 grit sand paper to knock down any lumps or bumps that might have occurred from raised grain or particles being trapped in the poly. 100 square feet should only take you about an hour and a half of labor total and then you shouldn't ever have to worry about water damaging the subfloor.

Q: We‘re renovating an old house, and the ceramic tile on the bathroom walls is just awful. I‘d like to replace the wall tile with beadboard. The tiles appear to be mortared directly onto the drywall. Is it a good idea to install the beadboard directly over the ceramic tile? Or should we chip of the tile or remove the lower portion of the drywall? I‘d like to do this as easily as possible, but not at the risk of shoddy workmanship.Also - all the beadboards I‘ve looked at are either painted or primed on the front surface, with a bare wood surface on the rear (glued to the wall). Is it advisable to paint/prime the rear surface as well before installation? With all the steam and moisture in a bathroom, I can envision the panels buckling. Is there a particular paint/primer that seals off from moisture particularly well?: It's better to remove the tile altogether, including the old backer board. We did that as insurance, we found there was no insulation in the wall so it was good that we did. Cover the entire wall with sheetrock (green board, meant for a wet location) then glue the beadboard in place with water proof adhesive (applied with a caulk gun). It's worth the extra time and effort for your own house and you'll know it's done correctly and will last for many years to come. Good luck, been there done that and still in the process. It's a labor of love, I guess! :o)

Q: I have glazed porcelain tile to put in my bathroom, but the thing is... that is is only 1/4 of am inch thick... Is it still okay to use it?...: glazed tiles are fine to use in the bathroom, the important thing to remember is if they are set properly and to set on either mortar base or hardiboard. the main concern though, would be whether the surface is too smooth a finish when used on the floor, especially when the tiles are wet! this could become a hazard to your health! a lot of tiles used in a floor application, have a sanded or rough finish ,just because of that !

Q: After completing a bathroom tile job, including a tile baseboard border about 6 up from the floor, we have dried thinset in on the actual wall - places we missed during cleanup. I‘ve tried using some scrapers (plastic and metal), and the dried thinset is like concrete (naturally) and is pulling layers of drywall off with it. Is there a solvent or better way to remove the dried thinset from both the wall and the exposed rim of the tiles? As a last resort I might be okay with slight damage to the walls as they need serious prep anyway before paint, but I do want to make sure i haven‘t missed some very obvious, easier, better solution first.: Rip, dig or pull it off. It has to come off and there is no trick way to do it. You can mud the damage when you prep the rest of the wall for painting.

Q: How long are ordinary white strip tiles?: There are four general specifications: 8 × 40 12 × 45 40 × 60 Commonly known as kicked tiles.

Q: Ok.. what i mean is this. Let‘s say you have hard tile beside the toliet and water damaged occured. Once you press down on the tile you can actually feel the weakness in the tile.. Does this automatically determine bad subflooring or is it possible just bad tile, Can I just killz over the subflooring repaint and lay new tile?: Does the tile wobble? It could mean the adhesive under the tile has deteriorated because of water leaks. Can you get under the floor and look up?

Q: Someone told me its called tile- something) I know it has a nic-name, do you know it?: Tile Row. It's on State College right past Anaheim Statium. My favorite tile store: Ed Pawlack Tile 601 W Lambert Rd. Brea, CA 92821 714.529.2364

Q: How to use ordinary drill drill on the tiles to hang things hanging?: Ordinary drill ~ more difficult to use, you can use a variable speed "impact drill" "can rarely smash the tiles. When drilling with a very slow speed to impact, and so on through the tiles can be full impact after the full The

Send your message to us

*Email

*TEL

*Quantity

*Unit