Glass Fiber Gypsum Board Wall/Roof Covering Cloth
- Supplier:
Taishan Gypsum Co., Ltd.
- Ref Price:
-
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 m²
- Supply Capability:
- 1000000 m²/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Specification
Formaldehyde:
E0
- Q: how do you hold insulated plasterboard on the ceiling while you drill it?
- you have about 3 choices..... rent a stand you put the bord on it then hand crank it to the cieling......or get some 1 to help you....or make a tool its just a couple of 2x4's nailed together to form a T make the long part of the T a little bit longer and just kick it in on a slight angle
- Q: Gypsum board has no formaldehyde
- Gypsum board does not contain formaldehyde, gypsum board production was mainly based on building gypsum. Can be assured that use.
- Q: Used to ceiling
- 1. ordinary paper gypsum board: ivory white paper, gray back paper, is the most economical varieties. Applicable to non-special requirements of the use of places, the use of continuous relative humidity of not more than 65%. Because of the price reasons, many people like to use 9.5mm thick ordinary gypsum board to do the ceiling, but because the 9.5mm plain paper gypsum board is relatively thin, the intensity is not high, in the recent more rainy wet conditions prone to deformation, Recommended to do the best choice for more than 12mm ceiling gypsum board. At the same time, the use of thicker plates is also an effective means of preventing joint cracking. 2. Water-resistant paper gypsum board: green paper, green back, its core and face paper have been waterproof. According to the requirements of the national standard, water-resistant plaster board and board core must meet a certain degree of water requirements (surface water absorption of not more than 160 grams, water absorption of not more than 10%). Suitable for humid places and areas with high humidity. In the most recent rainy season, it is best to use water resistant plasterboard. Waterproof paper gypsum board for continuous relative humidity of not more than 95% of the use of places, such as bathroom, bathroom and so on. 3. Fire-resistant plaster board: red paper, gray back paper, the core of the core to increase the refractory materials and a large number of glass fiber. If you cut the gypsum board, you can see from the cross section to see a lot of glass fiber. Good quality refractory plaster board should choose a good refractory performance of alkali-free glass, the general products are used in the alkali or high alkali glass.
- Q: I have put my flat screen tv on the wall but now all the wires are hanging down from my tv to my sky box and my xbox etc. I have drilled a hole behind my tv and a hole near the floor so that I can drop the wires through to make it more tidy. I tied the cable to a wire coat hanger to push it though but the cavity is filled with insulation and i cant push the wires through to the bottom. Also there might be joists that I haven't found yet. Does anyone know an easier way of doing this?Thanks
- Get a wire puller and insert it between the the drywall and the insulation vapor barrier(paper or plastic). There shouldn't be any joists in the way unless you have a split level house. If there is an obstruction it is probably conduit or fire blocking. I ran into fire blocking when doing my house and had to cut open dry wall and drill a hole to feed the wires through. Then I got expandable fire blocking foam to spray around in the hole with the wires after they were pulled. Lastly put back on the drywall and tape and paint. This was a lot of work but worth it for the look of a flat panel on a a wall with no wires showing. Or you could get track to put on the wall to conceal the wires that can be painted to match wall color and almost disappears.
- Q: Gypsum board small production equipment how much money
- You intend to do what size, and if it is a small workshop class, may also be hundreds of thousands (registered capital, equipment, plant, personnel, taxes, etc.) If the medium, about 2 million or so (my boss was doing this before, medium-sized, investment 2.58 million) It's hard to say it's big. The The But also to ensure adequate follow-up funds to prevent cash flow is not working
- Q: when skimming walls, can you do it over backing paper or does it have to be directly on the plasterboard??
- I'm no expert but would think you would need to remove backing paper before plaster goes over it , or paper will become very wet and start peeling away with plaster attached ........................... :)
- Q: What is the proportion of gypsum board?
- Gypsum board generally used surface density measurement, for example: 9.5mm thickness gypsum board, the national standard requires its surface density to be less than 9.5Kg / m2, but most of the better quality gypsum board density control in (6.5-7.2) Kg / M2. If compared with the density of water, the proportion of ordinary gypsum board is less than water. But the refractory board due to gypsum core inside the addition of glass fiber, depending on the amount of added, the density may be greater than the density of water.
- Q: Light steel keel gypsum board ceiling of the main keel spacing and vice keel spacing is how much?
- Hanging spacing of 1.0 meters, the main keel spacing of 1.0 meters, the distance between the keel 0.4 meters.
- Q: We have recently had a fairly big extension and now a considerable amount of our walls are plasterboard. I had painted one room a couple of months ago and now some of the screws have popped through from the plasterboard. I am now at the point where I need to paint my hall but I am reluctant to do this if some of the plasterboard screws are going to show through again. Should I get the walls skim coated or if any of the screws were going to pop would they have done so by now. Also is it expensive to skim coat?P.S I did paint the bathroom ceiling and first coat the surface was fine, went to give it a second coat and one of the screws had 'popped' Am I doing something wrong with the paint?
- sounds like the screws were not properly set or sealed to begin with- probley just poor workmanship. Just so ya know after the screws are put in they need to be sunk in a bit with some pressure - then sealed with mud or patch. I would guess your contractor did that already. ? and are you sure they used screws? i only ask cause sometimes nails are used and they pop causing the problems you mentioned- but the right screw is used it is uncommon that would happen. If you live in a moist area where there is high humidity - it is possible that the plasterboard has expanded a bit pushing the screws out- you can have the humidty levels checked - or you can probley feel if there is excess moisture in the room and maybe that can be cleared up with good ventilation. It is also possible they did not use a long enough screw, or the beam was not hit when it was screwed in- if thats the case then there probley is no remedy except basicly removing all the screws and repositioning them.
- Q: What are the classification and use of gypsum board?
- use Gypsum board is widely used in residential, office buildings, shops, hotels and industrial plants and other buildings within the partition walls, wall panels (instead of wall plaster layer), ceilings, sound-absorbing panels, ground floor boards and various Decorative panels and so on.
Send your message to us
Glass Fiber Gypsum Board Wall/Roof Covering Cloth
- Supplier:
- Taishan Gypsum Co., Ltd.
- Ref Price:
-
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 m²
- Supply Capability:
- 1000000 m²/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
