G Series Mono Screw Pump
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 5000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Performance Range:
Maximum pressure:Single stage 0.6MPa
Two stage 1.2MPa
Three stage 1.8MPa
Four stage 2.4MPa
Maximum capacity: 300 m3/h
Maximum temperature: 150°C
Maximum viscosity: 2.7*10^5cst
Feature:
Low Mechanical Vibration,No pulsation,Quiet operation,High suction ability
Could pumping liquid mixed fibre & solid grain,high viscosity liquid or mixed air liquid.
1. Good self-priming performance
2. Stable flow and minimum pulse shear
3. Wide range in viscosity of conveying medium, even the non-artesian medium. Non sensitive to the liquid
impurity.
4. Simple structure, high efficiency in operation: long service life, small abrasion,convenient main tenance and
replacing of rotatable parts
5. Operating and flow directions are reversible: multiple mounting forms
6. High utility ratio not easy to trouble.
Conveying Medium:
1. Neutral or corrosive liquid
2. Clean or wearable liquid
3. Non-current viscous liquid
4. Liquid with fiber and high solid content
5. Liquid with gas easy to produce bubble
Application:
Food industry: Pumping food liuqid,wine,waste liquid or additive liquid
Textile mill: Pumping fible liquid,dyestuff,printing ink,nylon powder liquid
Paper industry: Pumping back liquor
Petro industry: Pumping oil,grease
Chemical industry: Pumping suspend liquid,emulsion,soda & salt liquid
Shipbuilding: Pumping residue oil,sewage or seawater
Building industry: Pumping slurry,Cement
Nuclear industry: Pump rediocative liquid
Metallurgical & Mine: Pumping oxide or waste water,drain off water,liquid explosive
Watertreament: Pumping slurry,sludge,additive liquid
Power plant: Pumping coal slurry
- Q: What are the general water pump failure, how to repair?
- Troubleshooting of water pumpFirst, the water pump does not cause water analysisThere is air in the inlet pipe and pump body(1) before the water pump is started, the water is not filled enough. Sometimes it seems that the water has been discharged from the vent hole, but the pump shaft is not rotated. The air is completely discharged, resulting in a small amount of air remaining in the inlet pipe or pump body.
- Q: What are the advantages and disadvantages of the pump control system and valve control system in the hydraulic system? How to choose in the project?
- Pump control system is generally used for closed systems, the flow of the oil pump changes to control the motor or cylinder actuator action. The utility model has the advantages that the principle is simple, and the power of the engine can be fully utilized. The disadvantage is that the calorific value of larger, relatively poor precision.
- Q: What's the pump? Where can I use it?
- A pump is a machine that transports liquids or pumps liquids. Pumps are ubiquitous in life. They can be used to transport liquids such as water, oil, acid and alkali, emulsions, suspensions and liquid metals, as well as liquids, gas mixtures, and liquids containing suspended solids.
- Q: Concrete pump 125 pipe wall thickness
- Concrete pump, also called concrete pump, consists of pump body and pipe. The utility model relates to a machine for continuously conveying concrete along a pipeline by utilizing pressure, which is mainly used for building, bridges and tunnels
- Q: Does the reservoir water heater press the booster pump (high marks)?
- The outlet water pressure of hot water is the same as that of cold water. The water heater is pushed by cold water to push out the hot water. (of heating). Installation location about 2 meters away from the ground, the impact of water pressure is not large, in rural areas, the installation position in more than two buildings will have an impact. In the city, the installation position is above four floor to affect the water pressure.
- Q: The working principle of magnetic pump
- Structure characteristics1. permanent magnetPermanent magnet operating temperature range is made of rare earth permanent magnet wide (-45 - 400 DEG C), high coercivity, magnetic anisotropy direction is very good, also won't happen in the same demagnetization phenomenon when is close, is a good source of the magnetic field.2. isolation sleeveIn the metal isolation, isolation sets in a sinusoidal alternating magnetic field, in a cross section perpendicular to the direction of magnetic field lines induced eddy current and converted into heat. Eddy current expression is:. The Pe - K constant; eddy current; rated speed of N - T - pump; magnetic drive torque; F - the pressure inside the sleeve; D sleeve diameter; a material resistivity; and the tensile strength. When the pump design is completed, N, T is the given conditions, to reduce eddy current only from F, D, and so on. Non metallic materials with high resistivity and high strength production isolation, in reducing the eddy current effect is very obvious.
- Q: How many concrete pump tube diameter
- High pressure is the outer diameter is Phi 140 Type 150 type low pressure pipeline; pipe diameter is Phi 159 pipeline, high pressure pipeline diameter is phi 168.
- Q: Why is the sewage pump device coupler?
- The automatic coupling device but the installation of GAK type submersible sewage pump, need lifting, people may not need to unscrew the screw water, the water pump can directly improve, after repairing down along the guide rail can realize sealing pump and pipeline, water pump and normal operation. Small sewage pump can be installed freely, large sewage pumps are generally equipped with automatic coupling device, automatic installation, installation and maintenance is very convenient.
- Q: No negative pressure water supply equipment, both the main pump and auxiliary pump, power is not the same, how to choose the control cabinet?
- 1) microcomputer frequency conversion control cabinet2) water pump unit3) current stabilizing compensator4) vacuum suppressor5) all kinds of pipe fittings, valves and so on
- Q: How long does the fine stone pump need maintenance? What should I pay attention to?
- Daily maintenance of concrete pump, that is, routine maintenance in use, including inspection, cleaning, lubrication, fastening, adjustment, leak hunting, supplement of hydraulic oil, etc.. 8.1 hydraulic components inspection, due to the complexity of the equipment, we recommend practical experts to carry out the inspection of hydraulic system. If a fault is found, check the cause and repair the entire loop before proceeding to any operation. - found that oil has diarrhea, excluding leakage reasons. - inspect safety valves, hydraulic systems, steel tubes and hoses, fittings, cylinders, and find any wear and tear (pipe explosion may cause very serious consequences)
Send your message to us
G Series Mono Screw Pump
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 5000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords