Cantilever Formwork with Durable Performances and Trustful Quality
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 300 pc
- Supply Capability:
- 3000000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Structure of Cantilever Formwork Description
Cantilever Formwork is mainly used in the concrete pouring of pier, high buildings, and so on. The concrete lateral pressure is entirely supported by anchor system and the wall-through tie-rods, additional reinforcement is not needed. The construction is easy, rapid and economical. A single pouring height is high and the finished concrete surface is perfect. Cantilever formwork has several types, the structure is similar, and has its own different characteristic. Can use them according to actual demand.
Main cantilever Formwork：PJ200 & PJ240,CB-240 etc.
2. Main Features of Cantilever Formwork
-easy to assemble
-simple structure.
-easy, rapid and economical.
3. Cantilever Formwork Images
4. Cantilever Formwork Specifications
Anchor system
Anchor system is the most important supporting part. The system is made of five parts shown below. There into, tensile bolt, anchor shoe and bowl-climbing cone can be taken out for reusing after the concrete pouring.
① Tensile bolt M30/L= 110
② Anchor shoe
③ Bowl-climbing cone M30/D15
④ High-strength rod D15
⑤Ancor plate D15
5.FAQ of Cantilever Formwork
1) What about of our after-sale services?
. Response will be carried out in 24hours after receiving any complain or request.
. Any formwork cost can be refund after order is confirmed.
. If the products are not based on the requirements, there will be the relevant compensations made for you.
2) What about of our after-sale service?
. Response will be carried out in 24hours after receiving any complain or request.
. Steel Frame Formwork GK120 cost can be refund after order is confirmed.
. If the products are not based on the requirements, there will be the relevant compensations made for you.
- Q: How much is the adjusting range of the scaffold of the bottom
- Two, full scaffold installation requirements(1) the installation of the frame from the beam to the other end of the start, from the vertical and horizontal at the same time in the two directions, so as not to support instability. (2) all the rods used for supporting must be used before being tested.
- Q: I really want to get an industrial piercing but I'm going to a music festival in about a month... If I get it done this weekend, will a month be time enough for it to heal, because I plan on being drunk for that whole festival so I doubt I'll find time to clean it haha..Should I get it done, or wait until after the festival?..Thanks :) x
- hi, scaffolds take an prolonged time to heal as a usual rule and it is by technique of the certainty that 2 sections of your ear are decrease than stress (as they are actually related) merely shop cleansing it as you're doing and assume the discomfort to ease off. finished healing time could be around 8-12 weeks however the discomfort could supply up quickly as long as you do no longer bang it.
- Q: It's for my science assignment and I can't find the answer. Please help!! :)
- It is a way of making a bone strong enough to support body weight without having to be solid heavy bone.
- Q: I want to talk my mum into it.She might let me because it fits my school's regulations (two piercings/earrings per ear) but she might not because the holes are permanentI was wondering if the holes you get are a certain size, they might close up if you don't wear the earring for a while?And also, I'd like to know some health risks associated to getting one.Thanks.
- There are i think two different sizes you can get, and if you take it out, they will close up. Just do alot of reasearch on it, and show her your ready for it. Wooow, two ear piercings per ear, that suckkss. I have three in each lobe and a cartilage and tragus piercing. Soon industrial and anti tragus or rook. Sorry, and good luck!
- Q: A) what is the velocity of the brick after 4.0 s?B) how far does the brick fall during this time? This is using 9.8 m/s^2 as the acceleration
- v = a*t d = (1/)at^2 Plug in the numbers.
- Q: A 60.0 kg painter is on a uniform 25 kg scaffold supported from above by ropes. There is a 4.0 ? kg pail of paint to one side. Can the painter walk safely to both ends of the scaffold? If not, which end(s) is dangerous, and how close to the end can he approach safely?
- If both ends of the scaffold are supported by ropes then there is no chance of the plank rotating. OHS would still complain about the lack of handrails, the fact that the plank can swing without stabilization. Not to mention that ropes are unacceptable. They should be Nylon woven tape with fixed ends and at very least a one tonne rating. However that is not the thrust of your question. If the ropes are NOT at the very ends then by passing the rope on the end which has the 4 kg can of paint the whole plank may rotate about the pivot created by the rope. This will depend on where the two ropes are on the plank.
- Q: I'm getting scaffolding put up round my house. Its a Normal size house and its being put up all round the four walls to the top. will it be put up in 2 hours or more? or less? I have no clue please help me.Thanks!
- all depends how many guys are putting up the scaffold but I would say more than two hours
- Q: In the construction of the construction, the template and the selection of the scaffold has no corresponding specification
- Technical code for safety of steel tubular scaffold with couplers in JGJ130-2011 constructionJGJ128-2010 technical code for safety of steel tubular scaffold for building constructionTechnical code for safety of JGJ202-2010 construction scaffolding
- Q: truss or frame (?) which is preferred between the two in making scaffoldings and why?
- For stronger scaffolding you can use both..good luck
- Q: i need information for a black history project. his name is henry pickett the inventor of scaffolds or remaker however you want to call it. i need info like where was he born? when? wife? kids? what job he had? and stuff like that PLSSSSSSSSSSS HEELPPPPPPPP
- Henry Pickett did not invent scaffolds. Scaffolds have been used for thousands of years. He may have improved scaffolding in use at the time he filed his patent. Pickett, H.ScaffoldJune 30, 1874152,511 Check with patent office records to get details.
Send your message to us
Cantilever Formwork with Durable Performances and Trustful Quality
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 300 pc
- Supply Capability:
- 3000000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
