Submersible sewage centrifugal water pumpS

Submersible sewage centrifugal water pumpS System 1

Submersible sewage centrifugal water pumpS

Ref Price:

Loading Port:: Shanghai

Payment Terms:: TT OR LC

Min Order Qty:: 1 unit

Supply Capability:: 1000 unit/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

AY series oil pump

SK-3A water ring vacuum pump

Self priming 8 inch Centrifugal sewage electric motor pump

Refrigeration Oil Vacuum Pump

QY Oil-filled Submersible Pump

Submersible Pump for Dirty Water with WQ Series

Hot Oil Circulation Pump with High Temperature

High Pressure Booster Pumps with Pressure Tank

◊APPLICATION

Applied to pumping such liquid which is not clean, with solid matter or frictional matter, low viscous, lcorrosive, crystallizable, chemically neutral and close to water. Such as:

1. domestic wastewater treatment system

2. School,hospital,community wastewater treatment system

3. Irrigation

◊ Features

1. 100% copper wire

2. Cold-rolled silicon steel sheet, with high-speed punching, improve the efficiency and precision

3. Double sides mechanical seal graphite&ceramic

4. Demagnetization of stainless steel nuts

5. Anti-rust treatment castings and electrophoresis

6. New testing equipment

◊ OPERATION CONDITION

1.Maximum depth below water: 5m

2.Maximum trans medium temperature up to: 40

3.PH of trans medium is scope from 4-10

◊TECHNICAL DATA

description material
motor housing	stainless steel
pump body	cast iron
impeller	cast iron
shaft	AISI420(2GR13)
stator	DR510 steel
winding	100%copper
seal	mechanical seal graphite&ceramic

Q: How much water does the water ring vacuum pump run for an hour? If there is no steam separator, does the water vaporize?: For example: water storage is relatively small, it needs to reduce the temperature of the heat exchanger. If the tank is relatively large, it does not need cooling water circulation pump again when the temperature is very low, there is no need to heat exchanger. So you need to ask how much water this is not OK.In a soda separator problem:

Q: What are the characteristics of a pipe shield pump?: Four, high melting point in the pump hydraulic side and the motor side with a jacket, the jacket can be steam or a certain temperature of liquid to prevent high melting liquid crystallization. The outer circulation pipe of the pump should also be insulated (heating) jacket. Five, high pressure shielding pump shell is a high pressure container, so that the pump can withstand high system pressure. In order to support the shield under internal high pressure, the stator coil itself can be used to bear the pressure. Can also be made in high temperature and high pressure under the operation of the canned pump. Six, since the suction port of the pump impeller center is much higher than that in stopping the pump, when inhaled NO liquid in the tube, the impeller and the increase of the pump chamber is filled with liquid, and then start without irrigation, the pump can work. Self-priming pumps are especially suited for extracting liquids from underground containers. In addition, according to different methods can be divided into liquid type, mud type, high pressure pipeline type, as well as for ships, nuclear power plants and absorption refrigeration devices for various types of canned pumps. Can also be divided into vertical, horizontal, online and single-stage, multi-level and other different types.

Q: What is the principle of a turbopump?: Turbine [turbine] is a machine that converts the energy contained in a fluid medium into mechanical work, also called a turbine. Turbine is the transliteration of English turbine, derived from the Latin word "turbo", meaning "rotating object".

Q: Double floor sewage pump circuit diagram of a small problem: Question 3 when the water level is low, when the 1KA is connected, the pump will run depending on where your SS selector switch is located. Its left and right position, running pump and standby pump definition is different, left position is 1#, running 2# standby, right position is 2# running, 1# standby. Only inIn case the high level switch 2KA is connected, the standby pump may work at the same time.

Q: What is the lift off the dead center point? This is a straight mark about the water pump. What is the function and the relationship between the design head and the pump head? ThanksWhat exactly is the dead point lift? What's the function of this indicator?: Should shut down the valve bar, reduce the flow to increase the point of the head, it is best to adjust within the best range of work, otherwise it is easy to cause the current is too large, burning the motor

Q: Why should I pump the pump before starting the centrifugal pump?: Before the operation of the centrifugal pump, the pump must be filled with water, exhaust the air, before you start the operation. All centrifugal pumps should be handled this way, which is the centrifugal pump itself.The way of water diversion:1., in the centrifugal pump outlet increase water diversion pump (usually using vacuum pump), start the centrifugal pump before, start the vacuum pump, the centrifugal pump air into;2. increase the vacuum water tank before the intake of the centrifugal pump to meet the working conditions of the centrifugal pump;3. in the centrifugal pump inlet water increase valve, to meet the working conditions of centrifugal pump;4., if the water tank or water tank volume of water level is higher than the centrifugal pump position, the first operation of the front row empty, usually do not empty, you can use.

Q: What kind of motor does the hydraulic pump need?: The motor should be determined according to the work environment, such as 220V.12V.24V.72V or 380V, and then the power.Calculation of actual oil pump power:

Q: Hydraulic pump displacement refers to the pump shaft what?: Just as you carry a spoon to the water. How much water can you pump at once (every turn)? That's the displacement.

Q: No negative pressure water supply equipment, both the main pump and auxiliary pump, power is not the same, how to choose the control cabinet?: Non negative pressure water supply equipment can be divided into non negative pressure tank and box type non negative pressure compensation device, steady flow tank type non negative pressure water supply equipment is the negative pressure tank, pressure tank can eliminate the negative effect of network equipment, is equipped with a vacuum suppressor and water protection box; non negative pressure water supply equipment has the advantages of simple device is a water tank with the boost voltage stabilizing device of complex box at the same time with no negative pressure tank.The tank type non negative pressure water supply equipment adopts vertical multistage centrifugal pump. This kind of pump is low noise and high efficiency. Such as CDL series and imported CR seriesOrdinary box type non negative pressure water supply equipment can use multi-stage centrifugal pump, also can use stainless steel submersible pump, submersible pump costs will be lower, but the maintenance costs will be high.

Q: What is the difference between centrifugal pump and self suction pump? Which is better?: If the centrifugal pump in full before the start of the shell of the gas, then start after the center of the impeller was thrown in the gas can not be large enough to form the vacuum, so that liquid in the bath can not be sucked, so the centrifugal pump to start before using foreign liquid in the pump housing space filling

Send your message to us

*Email

*TEL

*Quantity

*Unit