Horizontal Multistage Pump

Ref Price:

Loading Port:: Shanghai

Payment Terms:: TT or LC

Min Order Qty:: 1 unit

Supply Capability:: 1000 Sets Per Month unit/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

CNBM Oil Pump

Multistage Centrifugal Oil Pump

Chemical Submerged Pump

Eccentric Helical Rotor Pump

High Speed Centrifugal Pump

Hot Oil Pump

Oil Slurry Pump

Pipeline Oil Pump

Multistage pump Introduction:HJD series of multistage pump is a centrifugal pump of horizontal, sectionalstructure, and is a successful product designed by our company.Its main features are: energy saving, designed by connection of the newest hydraul

Q: Motor home, in which case, the oil pump will not be able to pump oil: A lot of reasons, the oil pump damage, lack of oil, filter plugging, oil bottom touch, suppression, etc., will not get up because of oil.

Q: 498, just play the crankshaft, not oil, engine oil pump is new, and another one or not: Do not change the pump, oil change

Q: Motorcycle not oil, oil pump work well, oil road is not blocked, how to check?: If no oil, the first to check without cylinder plug, hit by electricity whether oil, if not, the oil pump idling, first check the oil, if the oil pump is normal, it is broken, oil pump is self-priming pump, can be suspended in the oil, air formed by its own tic, low pressure, make the oil upstream. If the low pressure zone leaks or the low pressure does not form, there is no oil.

Q: Santana pump engine sound big bad: The oil pump is broken, and it is easy to damage the engine because of bad lubrication!

Q: My car oil pump pressure is low, engine oil alarm idling always ring, how to do?: 1, lack of oil2, the oil leak, resulting in oil spills3. engine oil sensor fault causes oil lamp to be often bright

Q: What's the cause of the indicator light of the car oil pump?: In turn the ignition key does not start, oil should be light, because the engine lubricating oil channel has not been established in the oil, after the engine starts out as normal, such as after the start of light for the presence of faults, mainly due to the following: A: the oil shortage (more common)Two: the oil pressure switch (oil induction plug) fault (more common); three: oil pressure switch to the instrument between the fault lines exist; four: instrument fault (the possibility is very small: five) lack of lubrication system of internal pressure of the engine (more common) 1: dirty, too engine lubrication system within glioma lead, oil passages, set of filter clogging, so that the system does not establish normal pressure, 2: crankshaft bearing, connecting rod bearing, cam shaft bearing wear too much, resulting in failure to maintain lubrication pressure lubrication system, the machine oil lamps lit, 3: the oil pump internal blockage or too much wear, failed to build enough system oil pressure.The fault lamp is bright, must be timely to repair, did not identify the reasons before the engine will continue to drive the cylinder, crankshaft seizure fault, it must overhaul, to repair does not say, this is absolutely a damage to the engine.

Q: The van is out of order. What's wrong with it? Can it make a noise?: The direct burning tile lubrication system basically does not work. The oil won't come. All moving parts are dry milled

Q: Engine oil pump is blocked when the chain would ring: 1, the phenomenon is generally rhythmic sound, the sound is on the side of the camshaft, the noise is more than when the gear meshing uneven sound sharp. At low engine in speed, sound obvious and clear; increase the solar term door opening, the sound increases and becomes messy. In a few cases, a very heavy "click" sound can be heard, as if the camshaft bearings are seriously loose.2, reason oil pump shaft, distributor drive shaft bending or axial clearance is too large: oil pump drive main and driven gear, distributor drive, driven gear, crash or wear and tear deformation.3, check and judge this sound "fire test" test is invalid, you can touch the stethoscope at the lower end of the distributor body auscultation. If the noise is obvious, the body has a slight vibration, can be repeated from idle to low, medium speed throttle test. If the sound changes, as mentioned above, it may be this sound. If you hear a heavy click or click, as if the camshaft bearings are loose and loose, it is possible that the oil pump is broken.

Q: The carbon pump is blocked, the Walla fell, the total amount of money to clean the engine?: If the tile is gone, cleaning is no use

Q: How do you install the pedal motor pump?: Put the unit on the foundation with anchor bolts, between the base and the base, and use a pair of wedge pads.Release the axle shaft and place on the pump shaft and base with a level gauge. Adjust the level of the machine by adjusting the wedge pad and tighten the anchor bolts properly so as not to move around.Correct the concentricity of the pump shaft and the motor shaft, and allow the deviation of 0.1 mm on the outer circle of the axle shaft; two the clearance of the coupling plane shall be guaranteed 2~4 mm, and the clearance shall be uniform, and the tolerance shall be 0.3 millimeters.After connecting the pipeline and determining the direction of the motor rotation, then coupled with the coupling, and then check the concentricity of the shaft.In the actual test run 2~3 hours after the unit, for final inspection, if there is no adverse phenomenon, that the installation of qualified. Check the temperature and vibration of the bearing during the test run.During installation, all holes in the unit shall be covered to prevent debris from falling into the machine.In order to prevent the sundries from entering the pump, the filter shall be installed on the newly installed pipeline. The effective cross section shall be 2-3 times larger than the cross section of the suction pipe.However, the oil pump rarely fails, generally as long as the opening of the cylinder head, see more fresh oil or start the engine, there is oil jet, indicating the normal operation of the oil pump.

Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview

Location	Hunan,China
Year Established	2006
Annual Output Value	US$5 Million - US$10 Million
Main Markets	59.00% Mid East 8.00% North America 8.00% Southern Europe 5.00% Eastern Asia 2.00% Africa 2.00% Oceania 2.00% Southeast Asia 2.00% Western Europe 2.00% South America 2.00% Central America 2.00% Northern Europe 2.00% Eastern Europe 2.00% South Asia 2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability

a) Trade Capacity
Nearest Port	SHANGHAI,GUANGZHOU,DALIAN
Export Percentage	51% - 60%
No.of Employees in Trade Department	6-10 People
Language Spoken:	English, Chinese
b) Factory Information
Factory Size:	Above 100,000 square meters
No. of Production Lines	Above 10
Contract Manufacturing	OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range	High and/or Average