High Quality Silicon Carbide Ceramic Filter Plate Foam Filter Series
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 10000000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Ductile, Grey Iron, Vermicular Cast Iron and some Iron Alloy，and also for filtrating non-ferrous alloy, such as Cooper alloy and Aluminum alloy. It can remove impurities efficiently, and make metal filling steady in mould. It can also reduce air flow and casting impact in mould, and decrease pin hole, sand hole defeats to increase casting quality and product rate.
JG-202 Silicon Carbide Foam Filter
These series of products are newest products, which are produced through special material formula and latest advanced technology. Compared with normal ceramic foam filters, these new series products can be used at a higher temperature, which have higher strength at room temperature and high temperature. The physical property of this special material enables JG-202 series filters to have a better thermal shock resistance. They are suitable for harsh casting condition, such as placing on the bottom of vertical runner and casting at high temperature.
JG-203 Silicon Carbide Foam Filter
This product is produced through special material formula, and it has good durability, high thermal shock resistance and high porosity. It is mainly applied in filtrating heavy castings and medium-large casting, such as windmill, machine tool, ship parts and large part of mechanical equipment, etc.
Parameters
TypeMaterialsCompressive
Strength (Mpa)Porosity (%)Bulk Density
(g/cm3)Applied Temp.（≤℃）
JG-201SiC≥1.280-900.40-0.551500
JG-202≥1.578-900.45-0.601550
JG-203≥2.078-900.45-0.601500
- Q: What filter material are placed in the aquarium filter?
- Generally let off the filter cotton and ceramic rings, there are biochemical balls, coral bone, stone, activated carbon and so onConditional: filter cotton, ceramic ring, biochemical ball, coral bone, stone, activated carbon
- Q: What are the poor filtration effects of vacuum disc filters?
- The concentration can change the properties of the suspension, because the viscosity is no longer constant when the concentration of the suspension reaches a certain value, and belongs to the properties of non Newtonian fluid. For the suspension of fine particles, the filter cake resistance of low concentration slurry is higher than that of high concentration slurry, so the filter performance can be improved by increasing concentration. If the concentrate concentration is high and the general treatment capacity is high, the running overflow can be used to increase the concentrate content. The concentrate concentration is too high to influence the agitation, and the high productivity can be achieved by adjusting the overflow position.
- Q: The efficiency of ceramic filter is low. What's wrong with it?
- Ceramic filter by vacuum suction effect in the ceramic filter plate to cake drying purpose, ceramic filter plate needs cleaning and life, if you discover that the slurry sucking effect is poor or even grout should first consider these three aspects:Ceramic filter plateTwo factors of ceramic filter plate most likely, respectively is the rupture and plugging holes: the rupture will lead to distortion and poor vacuum cleaning; plugging holes will cause the filter plate suction effect is poor even if grout, ceramic filter plugging hole, can strengthen cleaning (such as shorten the cleaning cycle, prolong the cleaning time, increase the amount of nitrate), such as strengthening the cleaning effect is still not improved, it should consider the life approaching should be scrapped and replaced with ceramic filter plate new (replacement plate should not put new or different manufacturers is mounted on the same line, best can complete change).Vacuum system failureThe vacuum degree of ceramic filter is usually about -0.085MPa. If the abnormal vacuum is found, the normal vacuum suction can not be provided, and the suction effect will be poor, or even the pulp will not be sucked.If the vacuum is abnormal, should adhere to the vacuum pump, vacuum connection pipe is whether the fault Water Leakage leakage, distribution valve friction sealing, ceramic filter plate is connected with the rubber tube is aging or exfoliation, ceramic filter plate rupture.
- Q: What is the reason that the ceramic filter does not absorb mineral powder?
- There may be a fault filtrate pump, diaphragm pump damage, pump mechanical seal failure, a leak, two is no output or output to the liquid, the pressure is too low, the cleaning effect is not good, the pressure is too large, will cause damage and reduce the concentration of slurry filter plate.
- Q: How can I avoid the backwash pressure in the production of ceramic filter?
- Recoil of the ceramic filter is on the clean water under certain pressure, from the inside out flushing blockage blockage in the ceramic filter plate on the internal pore water pressure, the recoil is generally less than 0.12MPa, the pressure is too small or no recoil recoil effect is not good.
- Q: Excuse me, what's the reason that all ceramic filters do not attract ore?
- Vacuum system failure, no vacuum or vacuum can not meet the requirements. Should check the vacuum pump and vacuum piping, distribution head, ceramic plate, such as failure or leakage.
- Q: Ceramic filter suddenly do not smoke, a little later on their own good, what reason?
- The size of ceramic filter is generally on both sides of the vacuum tank, such as 50 square meters with 5 square meters of ceramic filter / ring ceramic filter plate combination (possible), there are 10 discs, the ceramic plate left a vacuum tank on the left of the 5 disc for filtration, vacuum filtration tank for the ceramic plate on the right right of the 5 disc. If a vacuum system temporarily fails, it may cause poor suction, no suction, and a normal operation at the other end.
- Q: Beneficiation ceramic filter no problem, the technical parameters are normal, but filter out the concentrate water suddenly excessive, what is the reason?
- Beneficiation of ceramic filter, the technical parameters are normal, but the water will fill in groove is what reason
- Q: What about the leakage of the ceramic filter static and dynamic sealing points?
- When the main shaft is rotated, the filter cake is adsorbed on the surface of the ceramic filter plate and dehydrated by the vacuum generated by the vacuum pump.
- Q: Can the ceramic plate filter the hot air?
- The vacuum degree of the ceramic filter in the vacuum system is about -0.085MPa. If the abnormal vacuum is found, the normal vacuum suction will not be available, and the suction effect will be poor, even without suction. If the vacuum is abnormal, should adhere to the vacuum pump, vacuum connection pipe is whether the fault Water Leakage leakage, distribution valve friction sealing, ceramic filter plate is connected with the rubber tube is aging or exfoliation, ceramic filter plate rupture.
Send your message to us
High Quality Silicon Carbide Ceramic Filter Plate Foam Filter Series
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 10000000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
