Good quality telescopic dump truck hydraulic cylinder 2014

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1.ISO9001:2008
2.Seal:Merkel or Parker
3.Working pressure:16-25Mpa.
4.10 years of experienc
5.Material:CK45

CMAX series engineering hydraulic Cylinder

(1)working pressure:16MPa

(2)Piston diameter: 40-250mm

(3)Seals:Merkel or Parker

(4)Sensor: MTS or Balluff

Q: 2. To make the piston move at 5m/min, what is the flow rate of the input cylinder L/min?: The flow is equal to the cross sectional area multiplied by the flow velocity,The flow rate in the problem is the piston movement speed, 5m/minThe area is 0.5 square decimeter decimeter, the flow rate was 50 per minute,So the flow is 25L/min

Q: Is it possible to change the hydraulic cylinder of the hydraulic lifting platform to the cylinder?: As long as you can bore is large enough, the theory on the line! But in fact, considering space and other issues, you can not change it.

Q: What kind of material is the hydraulic cylinder of loader?: 2, the cause of the wear and tear is mainly caused by insufficient lubrication. The piston and piston ring move at high speed in the cylinder mirror. Under lubrication. Between the working face can not form the oil film, both friction surface has extremely small part, the metal direct contact, because the friction formation partial high heat dissipation does not walk, but when accumulates to a certain extent, will cause two people to melt the adhesion. At this time, if the oil film can be timely recovery, cleaning and cooling, so that these tiny weld parts fall off without expansion; if the oil film recovery slow, weld expansion, resulting in abnormal melting wear occurred in a large area, which is usually called cylinder. Melting wear generally occurs on the upper part of the cylinder mirror, near the first ring at the top dead point, where localized metal melting is stuck and uneven uneven edges of groove marks and folds. Cylinderscoring phenomenon is easy to happen in production without running internal combustion engine immediately load working conditions. Because the internal combustion engine cylinder is not thicker, the oil film is not easy to form, and the cylinder mirror surface and the piston surface convex place often have tiny metal contact, thus causing melting wear and even killing phenomenon.

Q: Master, I want to make a set of hydraulic equipment for hydraulic piston and cylinder head with us how to adjust the tolerances. (H refers to the tolerance zone of the hole, f refers to the tolerance zone of the shaft, right? What does H7F8 mean?) I do not understand these written knowledge, it is best to say that the size of the piston head and cylinder bore how to fit, and can take specific figures for example, the best, the more detailed the better. To install the piston ring high speed heating will do, how to solve it, large caliber and long trip for us.: 1, GB standard: hole tolerance class with uppercase English letters, shaft tolerance class with lower case English letters, H7/f8 refers to the hole and shaft tolerance zone, but the specific tolerance depends on the size of the section, can be examined.

Q: Hydraulic cylinder application: Hello, hydraulic cylinder products are widely used in metallurgy, lifting, mining, transportation, ships, forging, machine tools, coal, oil, chemical, scientific research, military, and other industries. It is a hydraulic actuator that converts hydraulic energy into linear motion and mechanical work.The cylinder converts the pressure energy of the compressed air into mechanical energy, and the drive mechanism acts as a linear reciprocating motion, swinging and rotating motion. Mainly used in printing (tension control), semiconductor (spot welder, chip grinding), automatic control, robot and so on.

Q: How to use hydraulic system to control the feeding of machine tool table and the positioning and clamping device of workpiece: Two, the role of machine tools:A lathe is a machine tool for turning a rotating workpiece with a lathe tool. Can also be used in the lathe drill, drill reamer taps Banya and knurling tools for the corresponding processing. Lathes are mainly used for machining shafts, disks, sleeves, and other workpieces with revolving surfaces. They are the most widely used machine tools in machine building and repair factories.

Q: What is the cold drawn cylinder of a hydraulic cylinder? How about his quality? Master, help! Thank you: What do you do with it, if it is hydraulic cylinder, then we usually use cold drawn seamless tube here

Q: How to remove the hydraulic cylinder oil seal?: Is the O ring squeezed out? The front cover should be threaded, carefully to see if there are holes installed, there should be 2 or 4, is not to be painted over, if not, must use the flat shovel.

Q: What is the essential difference between hydraulic oil and lubricating oil?: Hydraulic oil is used for cylinder work! Lubricating oil is used for bearings! The place is different!

Q: Application of hydraulic and pneumatic in industry: This in the "SMC pneumatic service network" - technical article, there is an article devoted to pneumatic applications, you can look under,

Send your message to us

*Email

*TEL

*Quantity

*Unit