Single Acting Underbody Hydraulic Hoist/Ram For Trailer

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1.ISO9001:2008
2.Seal:Merkel or Parker
3.Working pressure:16-25Mpa.
4.10 years of experienc
5.Material:CK45

CMAX series engineering hydraulic Cylinder

(1)working pressure:16MPa

(2)Piston diameter: 40-250mm

(3)Seals:Merkel or Parker

(4)Sensor: MTS or Balluff

Q:2. To make the piston move at 5m/min, what is the flow rate of the input cylinder L/min?: The flow is equal to the cross sectional area multiplied by the flow velocity,The flow rate in the problem is the piston movement speed, 5m/minThe area is 0.5 square decimeter decimeter, the flow rate was 50 per minute,So the flow is 25L/min

Q:always have hydraulic oil leakage, please expert advice, with what seal can avoid, the best zero leakage.: 200 / min work frequency, high viscosity, slow flow, affect operation sensitivity.It is precisely the year that is too low to cause disclosure. Try to increase viscosity properly.This is a contradiction.

Q:machinery and components, such as cylinders, cylinders and so on, whether the pressure vessel ah? Does the relevant manufacturer need relevant qualifications? FiveThere are two entirely different answers to the question. Which one is right? Hope that professionals pointing. Thank you: Does not belong to pressure vesselOnly containers that meet the following three conditions are called pressure vessels:(1) work pressure (Note 1) is greater than or equal to 0.1Mpa (working pressure means the maximum pressure (table pressure) that the pressure vessel may reach at the top of the normal working condition); (excluding hydrostatic pressure)(2) containers with inner diameter (for non-circular section, width, height, or diagonal, such as rectangle, diagonal ellipse, long axis), not less than 150mm(3) the working medium is gas, liquefied gas or liquid whose temperature is higher than the standard boiling point;

Q:What can be used in hydraulic equipment factory: Most of the factory are used, hydraulic equipment, machinery and equipment power source!

Q:Hello, which units use hydraulic pneumatic cylinders and more cylinders?. Thank you: The meter on the unit of the cylinder is big, but there is more.And the hydraulic cylinder bore is greater.

Q:One hundred1: cylinder 150D-71x-102: cylinder GTD-80/090-P17M3: cylinder XQGA125*160-CA4: hydraulic cylinder COA3110715.035: cylinder MAB125-165P6: hydraulic cylinder SCI80/56 H1765XV980YPSX7: hydraulic cylinder CA100*70*350T8: hydraulic cylinder COA3112458.029: pneumatic gate valve cylinder DN600I need to find each cylinder bore. Stroke. The diameter of the piston rod installation. Pressure rating!!!Urgent need for support for the master! Thank you！！！ (the more specific, the more important.)What's the form? Do not understand.. can not point out in detail...: Find the manufacturer of each cylinder, select a sample, and solve all the problems

Q:used as the form of a connecting rod or piston in an automobile crankshaft. What is the minimum allowable value for such a hydraulic cylinder?. This way, the supply of oil cylinder in the rear, I ask the output cylinder allowed the maximum number of transfer, such as cooling good, the highest output can be transferred. How many manufacturers are there in the market?.: Yes, but this requirement is very high, and the input power is also greater. I don't know what you do

Q:The difference between gas cylinder and cylinder: The cylinder body is small and big, can be constant speed and speed change (change convenience), the output adjustment is also easy to teach, the freedom of transmission is higher, but the maintenance cost and installation cost are taught high, and there is oil pollution problems

Q:What is the essential difference between hydraulic oil and lubricating oil?: Definition of hydraulic oil,Hydraulic oil pressure is the hydraulic medium used in hydraulic system with liquid pressure energy. It plays the role of energy transmission, system lubrication, corrosion prevention, rust prevention and cooling in the hydraulic system. For the hydraulic oil, should first meet the requirements of the hydraulic device in the operating temperature and the starting temperature of the liquid viscosity, the viscosity change of oil is directly related to hydraulic operation, transmission efficiency and transmission precision, but also oil viscosity temperature properties and shear stability should meet the needs of different uses of the proposed.Definition of lubricating oilLubricating oil is used in various types of machinery to reduce friction, protection of machinery and processing parts of liquid lubricants, mainly from lubrication, cooling, rust, cleaning, sealing and buffering.By contrast, some of the effects of hydraulic oils and lubricants are the same... But they differ in their environmental conditions and are higher than those for hydraulic fluids...

Q:What should be considered when the hydraulic pressure is changed and the pressure is changed? Is the cost of air pressure high relative to hydraulic pressure?: Consider 1, after the replacement function can meet the use requirements,2, after the replacement of equipment, there is still room for change.3, cost and replacement engineering difficulty4, the use and maintenance after replacement.5, environmental protection, mainly noise,

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range