Ductile Iron flanged Butterfly valve DN450

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Size	DN40mm-DN1400mm
Design Standard	API 609
End flange	EN1092 , ANSI 125/150# , DIN2501
Face to face	EN 558-1, BS5155 , ISO 5752
Top flange	ISO 5211

Body	Ductile iron,Stainless steel,WCB
Disc	Ductile iron,CF8,CF8M,C95400,C95500
Stem	SS416,SS420,SS431,SS316
Seat	NBR, EPDM, WRAS-EPDM
Suitale medium	Sewage, Sea water, Air, Foodstuff and Oil

1) Sizes:

DN40mm-DN300mm
2) Materials:
a) Body: CI(cast iron ,GG25 ) / DI (ductile iron ,GGG40)

b) Disc: DI / CF8 / CF8M / C95400
c) Seat: EPDM / NBR / TEFLON / VITON

3) Features:

a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.

b)Soft seat. Replaceable.Increase of service life.

c)Double half shaft without pin.

d) Square and short neck. Easy to stick scutcheon and cost saving.

Q: What's the size of the signal butterfly valve sleeve?: The structure characteristics and working principle: the top design electrical device the butterfly valve of the worm and the worm gear driving device, and with the stem straight connecting transmission. In the closed precision electromechanical device, opening mechanical instructions and imported electrical components and parts with rust proof valve.

Q: In the pipeline attached building Atlas 05S502, in the middle of a water meter and check valve, the two sides are divided into two butterfly valve, want to ask why to arrange this way, what is the role of the two butterfly valve?: Check the water gauge and check valve on both sides to facilitate the maintenance and replacement of water meter and check valve.

Q: Have an iron block, aluminum heads, solid roller lifters, Jessel rocker shafts, what should my valve clearances be cold, and hot??: Only way to be sure is to put clay on top of a piston and turn the engine over by hand and then measure the clearance on the indentation in the clay.

Q: Can the inlet and outlet of butterfly valve be reversed? Why? What will happen if the reverse gear is installed?: Hard seal butterfly valve in any case, the reverse loading will cause tight seal.

Q: Where are the exhaust valves, mud valves and butterfly valves?: The exhaust valve is used for the heating of the independent heating system, central heating system, heating boiler, central air conditioning, floor heating and solar heating system.Mud valve, also known as cover valve, commonly used in urban water plants, sewage treatment plants sedimentation tank bottom discharge sludge.Butterfly valve used in furnace, coal gas, natural gas, liquefied petroleum gas, city gas, hot and cold air, chemical smelting and power generation environmental protection engineering system, conveying a variety of corrosive and non corrosive media pipeline, used to adjust and cut off the media flow.

Q: What do you mean by manual butterfly valve DN100 D341X-10?: DN100 refers to the inside diameter of the butterfly valveD stands for butterfly valves3 represents the turbine drive4 represents the flange connectionThe 1 represents straight throughX is the representative of the Dengqen rubber seal10 represents the pressure of 1.0Mpa (10 kg)Butterfly valve (English: butterfly valve) refers to the closure of parts (valve or butterfly plate) for the disk, around the valve shaft to achieve rotation and closure of a valve, the main cut off on the pipe and throttling. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation. Butterfly valve is fully open to fully closed is usually less than 90 degrees, butterfly and butterfly stroke itself has no self-locking capability, in order to position the disc to install the valve stem on the worm gear. Using worm gear reducer, not only can the butterfly plate have self-locking ability, so that the butterfly board stops at any position, but also can improve the operation performance of the valve.

Q: 19 years ago i had a valve repair and now im due to have heart valve replacement. I heard that the metal valve make noise has anyone who has had the metal valve have this type f problem or any other problem with the metal valve it would be a great help if anyone could answer: tissue valve is better because you will need long term warfarin with metal one. metal ones have other drawbacks like amaemia too

Q: What's the difference between butterfly valves and check valves?: Butterfly valve is manual, only switch function.The check valve is an automatic valve, which prevents backflow of the pipe medium.

Q: Whenever sports cars are referred, people talk in terms of 'valves'. ex: v8, v12 etc. What does this all mean? Also they sometimes say that a v8 makes a great noise. why? How does the number of valves effects the performance? Many thanks.: the v is in reference to the motor its in a v formation v8 4 cyliders on each side v6 3 per side v12 6 pre side now the valves is how many are in each cylinder you usually have 3 or 4 valves per cylinder the more valves the more horsepower the more cylinders the bigger the engine

Q: Butterfly valve, two-way pressure and one-way pressure what is the difference?: The positive pressure and the reverse pressure, the pressure when the medium returns

Send your message to us

*Email

*TEL

*Quantity

*Unit