Chemical Axial Flow Pump

Ref Price:

Loading Port:: Shanghai

Payment Terms:: TT or LC

Min Order Qty:: 1 unit

Supply Capability:: 1000 Sets Per Month unit/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Axially Split Casing Double Suction Pump

Petrochemical Process Pump

Roto-jet Pump

Self-priming Chemical Pump

TCE Heavy Duty Petrochemical Processing Pump

Double Suction Split Casing Pump

CDL Stainless Steel Vertical Multistage Centrifugal Pumps

AC Solar Water Submersible Centrifugal Pump

They are widely used for agriculture irrigation, water conservancy, water supply &drainage of civil engineering and farmlands, pollution treatment as
well as used in salt factories, raise, power station , docks for water lifting and falling, metallurgy and chemical industry etc

Q: Sometimes, cutting machine, bending machine pressure is not enough, I do not know if the hydraulic pump is broken, how should I judge?!: If it is, sometimes the pressure is not enough, not often. Then I don't think the oil pump is likely to go bad.The main reason is the hydraulic valve or oil above.

Q: The car burning oil pump replacement must do: 1, there are many reasons, but also models (steam, firewood) and so on.2, long-term use of poor quality oil, or viscosity grade unqualified engine oil and other internal wear too large.3, under normal circumstances, the engine will burn some of the oil from the cylinder block, piston and valve lubrication, consumption within the relevant provisions of the national standard range for normal (GB/T19055), and vice versa. The lowest scale car burning oil is often accompanied by smoke or in a maintenance period is lower than the oil gauge oil level.4, long time does not change oil or too long delay, not timely maintenance; piston and piston ring due to the use of long, normal wear, or abnormal wear and tear caused by the gap is too large.5, in addition, there are valve seals, crankcase forced ventilation, PCV valve damage, congestion, oil pump pressure, or its own failure can also be caused.There are many reasons why, as you describe the content is not detailed, the temporary analysis so far.

Q: Today I heard the cabin with "abnormalsound kakaka", open the hood, it sure is not the sound of the engine, the engine abnormal sound from below, the noise is very clear, like gear sounds like a roller coaster, just started the sound when uphill, and the throttle is louder. Said the faster speed is louder. Open repair factory, the mechanic said the oil is not a talk ambiguously to oil, oil change, I don't believe him, home to search the Internet, there are two possible judgment: one is the abnormal sound of valve rod hit what caused by catheter, pump two is bad, not to pump oil.I do not understand the car, I hope to have a professional friend to help me judge, in the end what is the reason, in the end is not serious? The car is new Elysee 16V. Is it the beginning of winter without preheating? StopI went to another repair shop today and said the valve was broken. I don't know. Isn't it serious?: Or should the hot hot restart

Q: A S195 diesel engine has changed main shaft, main shaft tile, engine oil pump, connecting rod tile, engine oil also does not burn, engine oil power is also new, half an hour indicator will not come up, beginning indicator pressure is very enough. No, the spindle will go down in 5 minutes. It has been broken several times. You've been driving for ten or twenty years. Can you do me a favor?Don't pull up indicator will score, gear edge: The only reason the indicator does not come is that the oil pressure of the indicator is not enough. According to this principle, the reasons for insufficient oil pressure are eliminated one by one. It should be noted that the replacement of new parts may not necessarily be good. As long as the oil pressure is not enough, or the oil pump problem, or the problem of oil, or that there is a certain place of normal leakage of oil, causing the arrival indicator oil pressure is small.First make sure the oil pump, the method is very simple, to another machine try glance. When installing the oil pump, be sure to pay attention to the leak. Check whether the oil is fake and shoddy. By the way, check the indicator and you'd better change it to another machine. If the above is no problem, you can basically determine the normal leakage of oil. For many reasons the oil leakage is very complex, with the main bearing and the crankshaft, the new fit is not necessarily good, with the clearance of additional oil, there is the crankshaft oil plug, whether tightening. As long as you check the oil path carefully, you will find the cause of insufficient pressure.

Q: The three price difference increases, I want to know the oil induction plug and oil pump parts price about what?: The three price difference increases, I want to know the oil induction plug and oil pump parts price about what?

Q: Do you need to disassemble the chain for replacing the oil pump of TOYOTA corolla?: Hello, you need to remove the timing housing, you do not need to remove the chain.

Q: Iveco oil pump driving wheel how down have special tools for heating 200 degrees: The oil pump can not be repaired by itself, nor can the repair factory repair it

Q: How to dismantle the oil pump chain saw: The language is hard to express. Just look for the video on the Internet

Q: Why is the Honda engine oil pump so big? What's the function of the other parts?: The balance shaft is the same as the oil pump, so it is larger.

Q: How does the c4l determine whether the oil pump works? The oil lamp is on: Check that the oil is adequate, enough, that is, the oil pump to be replaced

Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview

Location	Hunan,China
Year Established	2006
Annual Output Value	US$5 Million - US$10 Million
Main Markets	59.00% Mid East 8.00% North America 8.00% Southern Europe 5.00% Eastern Asia 2.00% Africa 2.00% Oceania 2.00% Southeast Asia 2.00% Western Europe 2.00% South America 2.00% Central America 2.00% Northern Europe 2.00% Eastern Europe 2.00% South Asia 2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability

a) Trade Capacity
Nearest Port	SHANGHAI,GUANGZHOU,DALIAN
Export Percentage	51% - 60%
No.of Employees in Trade Department	6-10 People
Language Spoken:	English, Chinese
b) Factory Information
Factory Size:	Above 100,000 square meters
No. of Production Lines	Above 10
Contract Manufacturing	OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range	High and/or Average