Cheap Prefab Shipping Container Homes

Ref Price:: $3,450.00 - 4,216.66 / set

Loading Port:: China Main Port

Payment Terms:: TT or LC

Min Order Qty:: 5 Sets set

Supply Capability:: 500 Sets per Month set/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Detailed Product Description

prefab shipping container homes

1. Easy to installing and low-cost.

2. Small and exquisite, easy to disassemble movement.

3. Strength structure, sealing, insulation, water-proof, fire-resistant and good for moisture-proof.

4. Breaking the traditional concept, our special design is convenient for the move and without any charge of disassembling; it will decrease the cost of construction so that the sandwich portable house is fit in the project site.

Q: I see, manual roller bearings, bearing room width is significantly greater than the width of the applicable bearings (bearing room 65, bearing thickness only 37), I would like to ask the outer ring bearings in the bearing seat in the axial direction of how to fix, plus GASKET?: This one is still fixed

Q: 1515 what kind of bearing is the bearing seat with?: Hello, I am Xiangshui long shaft bearing factory, Wuxi long shaft bearing Co. ltd.. You said 1515 with bearing model is: 1215K 2215K, thank you, I hope to help you busy ~!

Q: Does each type of bearing have GB bearing seat? Or is it replaceable? There are some basic block bearing and bearing seat GB?: No, some bearings don't have bearings. They need to be mounted on the shaft. If there is no bearing seat bearing, you can order the bearing seat. Red bearing dawn

Q: How can I check the concentricity of the bearing seat?: Coaxiality can be checked with a coaxial meter. Check the main sleeve socket before checking and tighten the bearing cap with the specified torque. The tester is positioned with the front and rear two bearing holes, and the mandrel can slide or rotate along the two locating sleeves. When checking, the mandrel moves along the axial direction, and the measured value of the contacts in different seats is the coaxiality of each seat hole after the two holes of the frying hole. National standard provisions: who can wear alloy compensate concentricity error with the reduction. In both ends of cylinder crankshaft bearing hole common axis as a benchmark, to have a crankshaft bearing hole of the coaxial tolerance must be 0.15mm, the instrument, the main bearing seat hole coaxiality error can also be used to test rod (available lever instead) and to measure the upcoming test feeler rod is inserted into the seat hole, with a feeler gap between the seat hole and the measured value is the test rod coaxial error.

Q: 6312 what type of bearing seat is it?: 6312 is bearing codeWhat you want is the bearing seat, that is, type 312, such as SN312

Q: Tapered roller bearings. The installation is complete except for the shaft ends. Therefore, only with glib lubrication.: Just above, as long as it's convenient to refuel!

Q: How about the expansion of the cast iron bearing pedestal? How do you heat it? How much is it heated?: Bearing housings and bearings are generally transitional coordination, the general nodular iron bearing seat heating to 85 degrees C is enough, the temperature should not be too high, high temperature, too much interference, useless, and easy to cause phase change, 85 degrees C enough. Oil bath heating, slowly warming, and then insulation for 1-2 hours, you can also use electromagnetic heating, but if the seat is too large, the electromagnetic is not good, uneven heating.

Q: Bearing seat processing what lathe, as far as possible to say specific points, not to the phone line, the adoption must be re - thank: If there is no rule, there are four claws, which is correct.

Q: I want to buy a group of bearings with bearing housings, bearings should not be spherical, or have bearings, hair pieces,: I don't know what you have in mind. I can make it as ordered

Q: 6305 what type of bearing is used in the bearing?: You can choose a lot of bearing hole and 6305 outer diameter of the same type of bearing seat in inner hole, and the width, most need is the choice of connection form, the general is two kinds of connection, and the same to the fixed bearing axial and vertical direction is fixed, this is no other requirements, such as single and double ring, lubrication and so on. I only know that P and FL vertical flange type (fixed form is said above), the best you need to go to the dealer according to the bearing, less demanding words should be easy, a lot of demand the best of yourself for a non standard.

Our company specializes in developing and manufacturing all sorts of prefab house and relative material since its establishment. We have made a well-known brand in the market and have a high speed developing guaranteed by out high quality. Our company possesses of integrated manufacturing equipment and experienced technical worker team. We got well reputation from society basing on sincere selling way, professional after sales service and rich manufacturing & installing experience.

1. Manufacturer Overview

Location	Guangdong,China
Year Established	2007
Annual Output Value	USD81,971,845.00
Main Markets	North America;South America;Southeast Asia;Africa;Oceania;Mid East;Eastern Asia;Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability

a) Trade Capacity
Nearest Port	foshan,guangzhou,shenzhen
Export Percentage	51% - 60%
No.of Employees in Trade Department	11-20 People
Language Spoken:	English, Chinese
b) Factory Information
Factory Size:	30,000-50,000 square meters
No. of Production Lines	6
Contract Manufacturing	OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range	High and/or Average