Living Converted Container House

Ref Price:: $2,587.50 - 3,162.50 / set

Loading Port:: China Main Port

Payment Terms:: TT or LC

Min Order Qty:: 2 Sets set

Supply Capability:: 200 Sets per Month set/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Detailed Product Description

converted container house:

1.used the high quality steel for structure,sandwich panel for walls,easy installation and remove,extensive usd for shop office

2.This kinds of container house used the high quality steel for structure, sandwich panel for walls, can easy installation and remove , so it extensive used for shop , office , villa ,house ...etc.

Usually it used more than 25 years , its standard size are have 20ft and 40ft, the layout can be design by you.

Technical parameters:

Wind resistance: grade 11 (wind speed ≤111.5km/h)

Earthquake resistance: grade 8

Live load capacity of roofing: 0.5kN/m2

External and internal wall heat transmission coefficient: 0.35Kcal/m2hc

Usage: offices, dormitory, hotel, remote building site, portable toilet and etc.

Package:

flat package, all components are well wrapped.

Q:What type of bearing does the bearing block SN222 match?!: The above students answer very comprehensive, in addition, I can add, SN222 can also use the same diameter, diameter, width and bearing more than, as long as less than the bearing seat installation size can also be used

Q:Can the bearing seat be made of cast iron?: Sure。 Cast iron can make all kinds of complicated workpieces

Q:How can I check the concentricity of the bearing seat?: Coaxiality can be checked with a coaxial meter. Check the main sleeve socket before checking and tighten the bearing cap with the specified torque. The tester is positioned with the front and rear two bearing holes, and the mandrel can slide or rotate along the two locating sleeves. When checking, the mandrel moves along the axial direction, and the measured value of the contacts in different seats is the coaxiality of each seat hole after the two holes of the frying hole. National standard provisions: who can wear alloy compensate concentricity error with the reduction. In both ends of cylinder crankshaft bearing hole common axis as a benchmark, to have a crankshaft bearing hole of the coaxial tolerance must be 0.15mm, the instrument, the main bearing seat hole coaxiality error can also be used to test rod (available lever instead) and to measure the upcoming test feeler rod is inserted into the seat hole, with a feeler gap between the seat hole and the measured value is the test rod coaxial error.

Q:The outer ring of the rolling bearing is fixed in the bore of the bearing seat, and the inner ring rotates with the shaft. What load does the outer ring bear?: Bearing internal and external ring load generally the same situation, mainly to see the bearing structure and shafting force situation, such as three penalty and cylindrical, cone force is not the same. But generally consider the moving coil interference fit, static loop transition or clearance fit.

Q:CAD drawings, bearing housings, bolt holes, specifications 2 x 4-42 * 52, what do these figures represent?: Front should be specifications 2 * 4, the back should be screws horizontal row row number 42 * 52

Q:What's the name of the screw hole in the bearing seat?: If the bearing body is estimated, grease cup hole for manual screw cap type grease cup, thread is M14*1.5 or M16*1.5 if the larger hole, M20*1.5, may be a thermometer hole.The bearing seat is provided with a screw hole, called a bearing seat hole, and provides a running base for the bearing and a mounting position for precise matching with the bearing.Bearing seat hole to achieve the precise size of the bearing requirements, and to batch size are unified, it is difficult to achieve in the mechanical processing, the use of new processing technology, processing is the urgent need for bearing users.

Q:How to handle the bearing block into the dust?: Switch to a bearing seat with a dust cover

Q:Do angular contact bearings have special bearing housings?: Angular contact bearings can bear radial load and axial load simultaneously. Able to work at a higher speed. The greater the contact angle is, the higher axial bearing capacity is. High precision and high speed bearings usually take 15 degrees of contact angle. The contact angle will increase when the axial force is applied.High speed precision angular contact bearings are mainly used in high load rotating occasions, requiring high precision, high speed, low temperature rise, low vibration and a certain service life. Pairs of high speed motorized spindle bearings are installed in pairs and are the key components of the high speed motorized spindle for internal surface grinding machines. Therefore, angular bearing can not be used with split bearing housings, because it is difficult to guarantee the accuracy of the installation

Q:How does the P207 bearing fit into the bearing seat and how can I remove it?: First, you can observe the bearing, to find out the bearing less there, observation of transposable elements, 0 elements and 180 degrees of the position will have two grooves, find the first step to success! Second, two feet fixed bearing seat, pipe, iron can get through the bore of bearing through the hole, bearing, toward the direction of 90 degrees, you can pry the observed bearing out (end) part of the top offset, you can use your wisdom to move on to the most, you can see the end position, will touch the bearing seat, then there put in the groove. The bearing can be removed back ` ` ` ` is simple, the bearing level into the groove inside, to 90 or 270 degrees to the direction of pressure, fixed seat, take the pipe to end in parallel and the seat pry will be installed, if you still do not understand, can contact me, or online video should have!

Q:Ladies and gentlemen:Ask a question, the outer spherical bearing block FS seat, online check is "with convex square block", but bought a sample back, with the F seat is the same, there is no lug. Now I can't figure out what the difference between the F block and the FS block isPlease know me under!! Thanks: The general is not replaced, FS no 200 series generalThe boss is opposite the FS illustrations F bottom is flat not protruding

Our company specializes in developing and manufacturing all sorts of prefab house and relative material since its establishment. We have made a well-known brand in the market and have a high speed developing guaranteed by out high quality. Our company possesses of integrated manufacturing equipment and experienced technical worker team. We got well reputation from society basing on sincere selling way, professional after sales service and rich manufacturing & installing experience.

1. Manufacturer Overview
Location	Guangdong,China
Year Established	2007
Annual Output Value	USD81,971,845.00
Main Markets	North America;South America;Southeast Asia;Africa;Oceania;Mid East;Eastern Asia;Domestic Market
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port	foshan,guangzhou,shenzhen
Export Percentage	51% - 60%
No.of Employees in Trade Department	11-20 People
Language Spoken:	English, Chinese
b)Factory Information
Factory Size:	30,000-50,000 square meters
No. of Production Lines	6
Contract Manufacturing	OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range	High and/or Average