Calcium silicon cored wire

Ref Price:

Loading Port:: China Main Port

Payment Terms:: TT OR LC

Min Order Qty:: -

Supply Capability:: -

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Specifications

1 factory supply with best price calcium silicon
2 calcium silicon cored wire
3 in this field with10 years old
4 :SGS/ISO

Product introducton

1 Calcium Silicon is compound alloy which is composed of silicon, calcium and ferro.

2 It is an ideal compound deoxidizer and desulfurizer which can be used in the production of many kinds of steel such as rail steel, low carbon steel, stainless steel and other special alloy like Ni base alloy and titanium base alloy.

3 CaSi alloy also can be applied as the heatraiser in convertor steelmaking workshop and as the inoculant or additive in producing cast iron and nodular cast iron.

4 factory very low price calcium silicon /calcium silcon powder /calcium silicon cored wire.Si content 50--65%,Ca 28--35%.

Speciafication

Brand	Chemical composition (%)
	Ca	Si	C	Al	P	S
	≥		≤
Ca31Si60	31	55-66	1.0	2.4	0.04	0.05
Ca28Si60	28	55-65	1.0	2.4	0.04	0.05
Ca24Si60	24	55-65	1.0	2.5	0.04	0.04
Ca20Si55	20	50-60	1.0	2.5	0.04	0.04
Ca16Si55	16	50-60	1.0	2.5	0.04	0.04

Calcium silicon cored wire

Q: In addition, the same furnace products out, the standard sample bar is qualified, no hole, but YT14 blade has more holes, why is that ah?: YT14 alloy you said, if the above holes can start from the following aspects, 1, raw materials, dirty and high oxygen content, impurity content, sintering, 2.If the hole shape of the dirty and dirty, you can see some holes around a circle with cobalt layer, small holes are filled with cobalt, cobalt pool formation, if not pressure, hole like narrow shape.

Q: What kind of carbide alloy is used in stainless steel processing?: The hardness of stainless steel is martensite, high hardness, using tungsten cobalt (do not use tungsten cobalt titanium, this is the 1 note) and Ta containing hard alloy.

Q: Carbide cutting insert: Brand in general can be found above, but you can also go to Zhuzhou tungsten tungsten alloy to see, they have good quality there

Q: What is the hardness of cemented carbide?: Different grades, different hardness, usually (86 ~ 93HRA, equivalent to 69 ~ 81HRC);

Q: the blade is hard alloy, the processing material is QT600, the plane lower tool margin is 4mm, the speed and the knife: This belongs to the category of ductile iron, more difficult to process, because the material is hard particles, it is recommended around S=1200 F=400

Q: What are the cemented carbide coatings?: The hard alloy coating is used to form high hardness wear-resistant coating on the surface of metal, Beijing Naimo company according to the composition of the alloy is divided into:1.jp8000 spraying tungsten carbide coating2. nickel tungsten alloy coating3. cobalt tungsten alloy coating

Q: What does American standard cemented carbide grain size C mean?: Then, when the mixture is granulated and pressed and heated to a point near the bonding metal (1300~1500 DEG C), the eutectic alloy is formed by the hardening and bonding of the metal. After cooling, the hardened phases are distributed in a grid of bonded metals that are closely related to each other and form a solid whole. The hardness of cemented carbide depends on the content of the hardened phase and grain size. The higher the content of the hardened phase and the finer the grain, the greater the hardness. The toughness of cemented carbide is determined by bonding metal. The higher the bonding metal content is, the greater the bending strength is. The effect of grain size on the mechanical properties of metals has a curve diagram: the strength of both ends is large and the middle is low. Explain: the mechanical properties of single crystals are very good. The finer the grain, the better the mechanical properties, but the mechanical properties of the single crystal with infinite size are much better than the grain's infinitesimal! A lot of grain size control method, the main principle of two: 1, increase the metal crystallization undercooling of 2, increase the crystal nucleus specific methods: electromagnetic stirring, adding grain refiner (such as Aluminum Alloy plus Al-Ti-C master alloy as grain refiner), lower solidification temperature, and fine grain of alloy elements and so on many.

Q: What is the hardness of the carbide thread?: The hardness of cemented carbide tools is generally between 89~92.8, such as the hardness of YG8 is HRA89, the hardness of YT30 is 92.8, and the hardness of YT15 is 91.

Q: What is the relation between the number of teeth of carbide saw blades?: 1., it is mainly used for longitudinal sawing of small diameter logs. According to the size of the pre adjustment, a plurality of sheets can be sawed off at one feed, which is widely used in the sawing process of the front path, small diameter and log sawing of blockboard and finger jointing factories. 2. compared with the band saw, the processing efficiency is high, the precision is high, the operation is simple and convenient, the technical requirement of the worker is not high, and the defects of low processing precision, low efficiency and high operation technical requirements of the band saw are compensated. What is the difference between the 1:40 tooth and the 60 tooth? Because of the small friction, the 40 teeth will save effort, and the noise will be small, but the 60 teeth will be cut more smoothly. A carpenter usually uses 40 teeth. The price is the same, ha ha. For small sounds, use thicker ones, but thin quality is better. The more the number of teeth, the more smooth the cut section. If your machine is stable, the sound will be smaller. What is the difference between the 2:30 wood cut saw blade and the 40 Tooth cut wood saw blade? Main: 1 cutting speed is different. 2 different gloss. The angle of the teeth of the 3 saw blade itself is different.

Q: What are the main causes of wear of high speed steel cutting tools and carbide cutting tools?: There are two reasons1. The tool itself quality problems of our factory has been recommended 3-turn Kuwait this brand2. Just the material, good hardness of material, speed, feed, reduce the point properly, can protect the tool wear well

Send your message to us

*Email

*TEL

*Quantity

*Unit