API610 Heavy Duty Petrochemical Processing Pump

Ref Price:

Loading Port:: Shanghai

Payment Terms:: TT or LC

Min Order Qty:: 1 unit

Supply Capability:: 1000 Sets Per Month unit/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Vertical Stainless Steel Centrifugal Pump

WQ Series Sewage Submersible Pump

Vertical Turbine Pump

Coal Chemical Pump

P.C Pump

Small Flow Chemical Process Pump

Standard Chemical Pump

Vertical Cantilever Pump

This type pump absorbs techniques in API610 the 10th edition and ASME B73.1-2001 standard, is a successful upgrade and innovation during the 7th five-year development plan in China.

Q: What's the cause of the indicator light of the car oil pump?: It's the oil pressure indicator, not the oil pump indicator light.This indicator is used to show the pressure of the engine oil. Open the key door. When the vehicle starts to self check, the indicator light is on and off after starting. The indicator light is always on, indicating that the engine oil pressure is lower than the required standard, you need to repair.If it's on all the time, just see if the oil is enough. How about the oil pressure switch, the wiring harness and the plug?. If it is flashing at some point, the possibility of a problem with the oil pressure switch itself is greater.

Q: What is the influence of insufficient oil supply in the oil pump?: Tank or pipeline bubbles; hydraulic system from "Ji, Ji" sound to ascend; the tractor has just started working device can improve the elevated temperature after a period of work, ascension is slow or not to upgrade; light load can improve, can enhance the expansion stage heavy load.Failure cause:(1) hydraulic tank oil level is too low;(2) do not use hydraulic oil according to season;(3) the tubing is seriously blocked by dirt;(4) the gear oil seal of the oil pump is damaged, and the air enters the hydraulic system;(5) the oil pump inlet, outlet port or bent joint "O" shaped sealing ring is damaged. The fastening bolt of the bending joint or the inlet and outlet pipe nut are not tightened, and the air enters the hydraulic system;(6) the inner leakage of the oil pump and the aging of the sealing ring;(7) oil pump end face or main or driven gear sleeve end face wear or scratch, two axle sleeve end surface roughness is over bad;(8) internal assembly error of oil pump causes internal leakage;(9) "left hand" installed "right" oil pump, causing the impact of the skeleton oil seal;(10) hydraulic oil is dirty.

Q: A S195 diesel engine has changed main shaft, main shaft tile, engine oil pump, connecting rod tile, engine oil also does not burn, engine oil power is also new, half an hour indicator will not come up, beginning indicator pressure is very enough. No, the spindle will go down in 5 minutes. It has been broken several times. You've been driving for ten or twenty years. Can you do me a favor?Don't pull up indicator will score, gear edge: I said immature advice, look at the body, the oil pump oil process hole is not exposed gas?. The phenomenon of air exposure must be reflected in the engine oil bubbles. Open the front cover, rotate diesel engine, find oil, solution,

Q: I am CB ZS200 recently found the engine abnormal sound their tune at the small valve clearance chain are good but there are still abnormal sound so doubt is not a problem of lubricating oil pump is not good for cam friction sound is that the machine in 2 years ago has changed because the oil pump oil pump cam is caused by the blockage ask the master how to identify whether or not the work: Start the engine first and see if there's any white smoke

Q: What is the cause of engine oil alarm?: 1, check the oil level is reduced, you need to add oil. 2, to the garage to check whether the sensor can be returned to normal, whether the line connection is firm.

Q: Reasons for heating of oil pump in roadheader: If you are using a high temperature oil pump motor may be caused by the following reasons: first, check whether the pump because of overload caused by fever; test method: with a twist of the hand to see if high temperature pump connector flexible operation, such as flexible and can be excluded: Two: check to see how the materials proportion is too large. If too much can cause motor overheating; Troubleshooting: re selection; three: when the working pressure is too large can cause motor overheating and Troubleshooting: can try to use high gear pump should be able to solve the problem of pressure; four: use range (flow head) over high temperature oil pump design requirements? Choose the right motor according to the serial type. Five: high temperature oil pump motor assembly and coaxial pump motor will not only of fever and noise during use will increase, solution: open angle screw, re check coaxiality, and then tighten the screws can be solved;

Q: The car leaked oil, changed a pump, put it up overnight, or a few drops of oil, and called the repair truck. He said it was dirt underneath. It was hot: Hello, no hot weather will flow down to say, in the repair work is completed, the oil will be on the left before the cleaning, is does not have that kind of the situation, I suggest you put the car into the garage rack up again and see if there is obvious for the maintenance of quality problems, can be put forward re construction to repair factory.

Q: I don't understand. How can the internal parts be bad, depend on it, it's depressing: Pull in the water or burn the oil

Q: How does the c4l determine whether the oil pump works? The oil lamp is on: The oil pump is basically mechanical, so you can try changing the oil sensor.

Q: What are the causes of motorcycle engine oil pump damage?: One: the quality of gasoline plus 90 oil, do not say that the damage to the oil pump, the vehicle engine damage is greatTwo: too much oil refueling, the pump burden is too large, too much overheating of the engineThree: the quality of the oil, the better the oil on the engine wear less, but ordinary 125 is not necessary to be so goodFour: the oil use time normally every 3000 to 5000 kilometers should change the old oil, does not change the old oil in the iron and the thicker oil itself will have a great damage to the oil pumpFour: the normal wear and tear of the machine, needless to say, is a bad day for everything

Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview

Location	Hunan,China
Year Established	2006
Annual Output Value	US$5 Million - US$10 Million
Main Markets	59.00% Mid East 8.00% North America 8.00% Southern Europe 5.00% Eastern Asia 2.00% Africa 2.00% Oceania 2.00% Southeast Asia 2.00% Western Europe 2.00% South America 2.00% Central America 2.00% Northern Europe 2.00% Eastern Europe 2.00% South Asia 2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability

a) Trade Capacity
Nearest Port	SHANGHAI,GUANGZHOU,DALIAN
Export Percentage	51% - 60%
No.of Employees in Trade Department	6-10 People
Language Spoken:	English, Chinese
b) Factory Information
Factory Size:	Above 100,000 square meters
No. of Production Lines	Above 10
Contract Manufacturing	OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range	High and/or Average