Stainless Steel Basket Strainer

Hot Products

Ductile Iron Gate Valve Non-Rising Stem of DIN3352 F4

Non-rising Stem Metal Seated Gate Valves Made of Ductile Iron

Three-way Control Valve Made In China Best Price

Bellows Seal Control Valve Made In China Best Price

Cage-guided Control Valve Made In China Best Price

Non-rising Stem Resilient Seated Gate Valve Made of Metal

Non-rising Stem Resilient Seated Gate Valve Made of Ductile Iron

Ductile Iron Gate Valve Non-Rising Stem of BS5163

J41F-16 fluorine plastic shut-off valve

Angle Control Valve Made In China Best Price

FAQ

A reading from my 2002 ford explorer said insufficient flow from the EGR valve. Would it be possible to clean the valve or fix it or would I need to buy a whole new valve?

It could be two things. The exhaust gasket coming to the valve or the vacuum coming to the valve. The egr did not need changing. Without the proper tool to check it out. I can not say which it is or how to repair. It need to go to shop where the proper test can be use to find what need to be repaired of replaced Most likely it will be a one way vacuum valve, that is not working right.

I have a D16Z6 SOHC VTEC engine in my 93 Honda Del Sol.Ive been told that the D16Z6 came with 2 different valve covers. One style cover says Honda on the top and another also says VTEC.I have the one that just says honda but I want the other put on.What would I need to swap them, and where would I get them?and a roundabout price

I don't think they sell any aftermarket valve covers that say Honda VTEC since companies would have to pay honda to use the name and i did a quick search but I could not find 1 cover for you vehicle which means you'd have to call the junk yards around your area or just call Honda and see if they can order one in for you, i doubt they have one lying around on a shelf it will take anywhere from 2 days to a week to order in and since its factory honda part its probably around 200$ without the gasket(maybe abit more) but if you swap it for a new one I suggest you do the gaskets and grommets with it so it won't leak oil. It's pretty fairly easy to change yourself, they are all top nuts or long bolts that run through the cover if i remember either 10 or 12mm, or both sockets required, when you get all the nuts off you simply just pull off the cover, it might be abit stuck so you can pry gently with a small screw driver or small prybar and it will come off, cover the top with a clean cloth or newspaper so no dust and rocks fall in, clean the metal area off of all the oil and youll see small corners that have abit of silicone on it, thats for extra protection so it won't leak out of the corners so just a small amount of black silicone dab in the same corners then put the new cover with gasket it on and tighten down, and just snug the bolts, theres no need to tighten the crap out of it or you might snap a bolt. 3/8 drive wratchet is okay to use. ( if you get some junkyard valve cover DO NOT paint it unless you have special heat ressistant paint or it will peel off and look really ugly ) Good luck....

To control a double solenoid valve, what do you recommend to use in my PLC program .... Do you recommend to use the SetReset coils or to use the normal coils?

You may want to check with the company that manufactured the valve - that would be your most likely source.

I have a 3406b motor. It has blow by. This happened when I hired a mechenic to do a top end. I belive that he did not ajust the valves correctly or something happen to the motor. I want to gap the valves to see if this helps out. How would I go on doing this.

try using this link here to help you out. Dont know if you have engine brake or not. but u should be able to still adjust the valves correctly if you follow along with the process.

When i disconnected my Diverter Valve and made it non-recirculating i drove down the street and my engine cut out on me. it will go a few feet and after the excess pressure is released (PSHH) the car cuts out. i reconnected the valve tubing making it rec-circulating and it works fine. im baffled i know VW is supposed to run a DV but last night i saw a stock VW GOLF running blow off and he was stock. any ideas? it is an after market DV made by forge.

The OEM valve has a very low spring rate against the diaphragm holding the plunger down. The very first time you released the throttle the engine vacuum easily held the valve open. When not in boost the open valve will become an intake leak because its bypassing the MAF (mass air flow) sensor. If the MAF reads very low air coming in through the it, the ecm will start lowering the injector pulse width until it cant compensate any longer and will cut off because of the air leak. The Golf was running a higher spring rate to keep the valve closed at idle or has a chipped ecu to be able to release to atmosphere. Hope this helped out.

I have varicocele and varicose veins. Both conditions are caused by vein valves becoming damaged or defective. My question is, is this a sign of more serious problems?Thank You

By following this guide book I was able to eradicate my varicose veins pretty fast. God bless!

It looks like our toilet water shut off valve is leaking. We are trying to turn off the water by turning the lever on the hot water heater, but this only turned off the hot water. So the cold water is still not turned off? We thought the one lever at the hot water heater would turn it all off, but it didn't work. Is there actually a separate water shut off valve for cold water in my house? Help!!

Every house should have a water meter and a shut off point close by. This will isolate ALL water cold and hot water included. With shut off valves, you can usually just take the guts out and replace them with the guts from a new one. Take a couple close up pics of your shut off valve and show them to a plumbing assistant at any DIY store such as Home Depot. They can find you the right product. In order to replace the guts, all you need is a larger crescent wrench and a set of channel lock pliers. I would recommend having a small bucket handy to catch any loose water. Prior to taking anything apart once youve shut the water off, I would run the cold water in a basement sink or main floor sink to reduce the pressure and water quantity.

What are the names of the main arteries and valves?????????REALLY NEED ANSWERS TODAY!!!!!!!!!!!

Main arteries: Aorta (oxygenated blood from heart to body), Pulmonary Artery (DEoxygenated blood from heart to lungs). Main Valves: Tricuspid valve (separated right atrium and ventricle to ensure correct flow of blood), Bicuspid Valve( separates left atrium and ventricle), Aortic Valve( ensures blood flow from left ventricle into aorta). hey sorry only saw ur question today:P hope it helps!