WQD/WQ High Lift Electric Sewage Water Pumps
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
PRODUCT INFORMATION
WQ series submersible non-clog sewage pump in the introduction of foreign advanced technology, based on the joint efforts by our researchers, while a wide range of suggestions from pump experts, and after many improvements and successfully developed, tested each Top performance indicators are that the advanced level of similar foreign producing countries. Used in chemical, petroleum, pharmaceutical, mining, paper industry, cement plants, steel mills, power plants, coal processing industry, and urban sewage treatment plant drainage systems, municipal engineering, construction sites etc sewage particles, dirt, can also be used to pump clean water and corrosive media.
Model significance
50WQ (QW) 25-32-5.5
50 caliber 50mm exhaust ----
WQ (QW) --- submersible sewage pump
25 ---- flow of 25m3 / h
32 ---- lift 32m
5.5 --- with motor power 5.5KW
Performance range
Flow: 7-950m3 / h
Head: 7-35m
Features
1. When using a unique monolithic or double blade wheel structure, greatly improving the living creatures capacity, can effectively through five times the diameter of the fiber material and pump caliber pump diameter of about 50% of the solid particles.
2. Mechanical seal with anticorrosive hard softening tungsten materials, can pump more than 8000 hours of continuous operation safety.
3. The overall structure is compact, small size, low noise, energy-saving effect is remarkable, easy maintenance, no need to build pumping stations, poured into the water to work, greatly reducing the project cost.
4. The pump seal oil chamber with high precision interference leakage detection sensors embedded in the stator windings of the thermal components, automatic protection of pump motor.
5. According to user needs with automatic control cabinet, the pump leakage, leakage, overload and overtemperature protection automatically improve product safety and reliability.
6. float switch can change depending on the desired level, the automatic control of pump start and stop, without special care, extremely easy to use.
7.WQ series according to user needs with double rail automatic coupling installation system, install it to bring more convenient maintenance, may not have to get into the sump.
8. be able to use in the whole head, but to ensure that the motor is not overloaded.
9. There are two types of installation, fixed automatic coupling installation system and traveling free installation system.
FAQ
We have organized several common questions for our clients，may help you sincerely：
①How about your company？
A world class manufacturer & supplier of castings forging in carbon steel and alloy steel，is one of the large-scale professional investment casting production bases in China,consisting of both casting foundry forging and machining factory. Annually more than 8000 tons Precision casting and forging parts are exported to markets in Europe,America and Japan. OEM casting and forging service available according to customer’s requirements.
②How to guarantee the quality of the products？
We have established the international advanced quality management system，every link from raw material to final product we have strict quality test；We resolutely put an end to unqualified products flowing into the market. At the same time, we will provide necessary follow-up service assurance.
③How long can we receive the product after purchase?
In the purchase of product within three working days, We will arrange the factory delivery as soon as possible. The pecific time of receiving is related to the state and position of customers.Commonly 7 to 10 working days can be served.
- Q: Fire hydrant pump button, under what circumstances do not need to install?
- There are four things to do:Fire hydrant button to meet the requirements of national standards.In addition to pumping, it can show the location of fire.
- Q: Must the water pump in the tank be all soaked in water?
- Of course, if the motor is overheated, it will burn, and the temperature of the water will drop down.
- Q: How much water does the water ring vacuum pump run for an hour? If there is no steam separator, does the water vaporize?
- The purpose of the steam separator is to separate the gas from the liquidWater ring type vacuum pump, water, compressed gas is discharged through the exhaust port, if not it is soda water separator is discharged, can not be separated, for the recovery of gas discharged industry is obviously impossible.Soda separator is available, the key is to see the working conditions
- Q: There are second cutting, third cutting, why three times?
- So some pumps are written in the back of XXXX-125A or B, that is, the impeller nominal diameter is 125, A is through a cut, B is the 2 cutting. To reach the applicable conditions, only the calculation is not enough, but also after cutting to test to determine.
- Q: Why can the centrifugal pump hold down the pressure?
- The pump before starting to pump shell and the water pipe filled with water, and then start the motor, the pump shaft to drive the impeller and water do high-speed rotation, centrifugal water movement, was thrown to the outer edge of the impeller, the pressure water pipeline flow through the volute pump into the pump shell.
- Q: Brief description of centrifugal pump on / off operation
- First, the preparation before the start(1) carefully check the inlet and outlet pipe line, valve, flange and pressure gauge joint of the pump, whether the installation is safe, comply with the requirements, whether the flow is correct, whether the anchor bolt and other connecting parts are loose or not.(2) add lubricating oil to the bearing case, and the oil level is 2/3 of the gauge of the bearing box.
- Q: What is the function of the heating pump system for the water pump design?
- Will cause some of the internal friction gap disappeared, the coupling center damage. In this case, starting the pump inevitably results in vibration, friction, etc.
- Q: How high can the pneumatic diaphragm pump be?
- If the pump material made of polypropylene (PP) material, corrosion resistance, good chemical resistance using PP material produced by pneumatic diaphragm pump can resist medium low cost, good generality, polypropylene material mainly is especially suitable for general acid-base liquid, using poly propylene made of plastic gas diaphragm pump can only withstand the highest temperature to 65 degrees, more than this number of polypropylene plastic deformation.
- Q: What are the main performance parameters of hydraulic pumps?
- Displacement and flowDisplacement refers to the pump (or motor) every turn a week, by the size of the sealing chamber geometry variable discharge (or enter) the volume of liquid, commonly used unit is ml/r (ml / rev). Displacement can be changed as a variable pump (or variable motor), and the displacement can not be changed into a quantitative pump (or a quantitative motor).Actual flow is the amount of flow at the outlet (or inlet) when the pump (or motor) is operating. As the pump itself leaks, the actual flow is less than the theoretical flow. As the motor itself has an internal leakage, to achieve the specified speed, in order to compensate the leakage, the actual flow of input must be greater than the theoretical flow.
- Q: Attention should be paid to the use of pumps?
- 7 water pump and pipe interface must be sealed, because if there is debris access, then the pump will cause damage to the interior. 8 for the water pump bearing is also the focus of inspection, use up to check whether the bearings wear,
Send your message to us
WQD/WQ High Lift Electric Sewage Water Pumps
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
