Steel Grinding Media Mill Ball with Well Abrasive Resistance Top Quality For Cement and Mineral Processing
- Ref Price:
-
- Loading Port:
- Qingdao Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25MTS m.t.
- Supply Capability:
- 200000MTS/Year m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Features of Steel Grinding Media Mill Ball with Well Abrasive Resistance Top Quality For Cement and Mineral
Processing:
1) High hardness: Steel Grinding Media Mill Ball has high hardness: surface hardness can reach to 55-67 HRC, volume hardness 56-64 HRC
2) High Impact toughness: impact toughness is more than 15 J / cm2.
3) Low Broken rate: peel fragmentation resistance property of over 20000 times. The actual breakage rate is less than 1% and close to 0.
Technical Parameters of Steel Grinding Media Mill Ball with Well Abrasive Resistance Top Quality For Cement and
Mineral Processing:
Nominal Diameter(mm) | Dimensional Tolerance(mm) | Roundness % |
Φ20 | ±2 | ≤6 |
Φ25 | ±2 | ≤6 |
Φ30 | ±2 | ≤5 |
Φ35 | ±2 | ≤5 |
Φ40 | ±2 | ≤5 |
Φ50 | +3,-1 | ≤4 |
Φ60 | +3,-1 | ≤4 |
Φ70 | +3,-1 | ≤4 |
Φ75 | +3,-1 | ≤4 |
Φ80 | +4,-2 | ≤4 |
Φ90 | +4,-2 | ≤4 |
Φ100 | +4,-2 | ≤4 |
Φ120 | +4,-2 | ≤4 |
Φ125 | +4,-2 | ≤4 |
Φ130 | +4,-2 | ≤4 |
Φ140 | +4,-2 | ≤4 |
Φ150 | +4,-2 | ≤4 |
Chemical Composition of Steel Grinding Media Mill Ball with Well Abrasive Resistance Top Quality For Cement and
Mineral Processing:
Name | C | Mn | Si | Cr | S | P | |||
60Mn | 0.57-0.65 | 0.70-1.0 | 0.17-0.37 | 0.25max | 0.035max | 0.035max | |||
65Mn | 0.60-0.70 | 0.90-1.2 | 0.17-0.37 | 0.25max | 0.035max | 0.035max | |||
75MnCr | 0.70-0.85 | 0.70-0.85 | 0.17-0.37 | 0.40-0.60 | 0.030max | 0.030max | |||
Specification of Grinding Media Ball | |||||||||
Nominal diameter | Diameteical Tolerance | Weight of single ball in average | Surface hardness | Impact toughness | |||||
(mm) | (mm) | (g) | (HRC) | (j/cm2 ) | |||||
Φ20 | +2 -1 | 32 |
55-65 |
≥12 | |||||
Φ25 | 64 | ||||||||
Φ30 | 110 | ||||||||
Φ40 | 263 | ||||||||
Φ50 | 513 | ||||||||
Φ60 | +3 -2 | 888 | |||||||
Φ70 | 1410 | ||||||||
Φ80 | 2104 | ||||||||
Φ90 | 2996 | ||||||||
Φ100 | 4110 | ||||||||
Φ110 | +4 -2 | 5457 | 50-60 | ||||||
Φ120 | 7102 | ||||||||
Φ130 | 9030 | ||||||||
Φ140 | +4 -3 | 11278 | |||||||
Φ150 | 13871 | ||||||||
- Q: What are the casting parts used to test shrinkage holes?
- 2. x ray. This method can do nondestructive testing, but the cost is higher. Generally, high castings are required.
- Q: What are the effects of stiffeners on castings, or on welded parts (for 2 tons or less), casting or weldments on stiffeners?
- 4, the performance requirements of the steel: whether castings or welding parts, there may be quality defects, but the casting will generally be worse than the weldment.You should be able to make a choice in the end.
- Q: How to distinguish the forging parts and casting parts accurately
- To distinguish from the use of materialsForging materials are mainly made of carbon steel and alloy steel of various components, followed by aluminum, magnesium, titanium, copper and their alloys. The original state of the material is rod, ingot, metal powder and liquid metal. The materials needed for casting are mostly metal, wood, fuel, molding materials and so on. In contrast, the forging parts rarely produce dust, harmful gas and noise, etc., and play a more obvious role in environmental protection. Of course, because of this, the price of forged parts on the market is higher than that of castings.
- Q: How do you mark it on the drawing? Do you need to discuss it with the manufacturer?Because the casting allowance is the standard, then, after all, is the theoretical value, the actual level depends on the manufacturer, so is it necessary to ask the manufacturer?
- The general foundry casting technology division will mark put shrinkage and the allowance of the map in your chart (usually with the red pen) for the production of wood or other material wood workers die drawings.
- Q: Would you please tell me how to use casting parts for a year?The cast of an aircraft wing needs to be put aside for a year before it breaks;Does anyone know why?
- There are various casting stresses after casting, which can be divided into two kinds: thermal stress and shrinkage stress. In a long time placed in the atmosphere, called aging treatment.Aging treatment is an effective measure to eliminate casting stress. Aging is divided into natural aging, thermal aging and resonance aging.1, the so-called natural aging, the casting is placed in the open field for more than half a year, so that the internal stress relief.
- Q: Why do casting parts have air holes?
- First, from the source, tools, raw material drying, in the process of melting into the reaction gas, another influence is pouring process, such as high temperature solidification gas dissolved too much after not excluded. The method can adjust the pouring temperature properly, control the source of gas (drying and controlling the inoculant, especially the content of magnesium), and add cooling iron to change the solidification mode. It depends on what kind of casting you are. You can't make it clear at once. And molding sand relationship is mainly water content and permeability, brush coating resin content.
- Q: Cause of choking of casting parts
- Choke fire is the process of pouring a large number of gases can not be discharged smoothly, boiling in the metal liquid, resulting in a large number of castings in the pores, and even incomplete casting defects
- Q: What foundry factories are used in the casting parts of China's major automobile manufacturers?
- Tangshan Yongding automobile spare parts factory also give a lot of supply, casting factory of Tangshan n to the car enterprises casting wheel gearbox etc.The team of casting experts welcome you to ask questions and accept questions!
- Q: Can the casting part be phosphating with the phosphating solution of the pickling board?
- Like stainless steel casting, duplex stainless steel casting is phosphating, ductile iron gray iron is not required
- Q: The difference between sheet metal and casting parts
- Casting parts are made by casting (followed by a variety of processing), the shape can be simple, can also be very complex, usually large parts, as a base, bed, work table, and so on, good seismic performance.
1. Manufacturer Overview
| Location | Shandong,China |
| Year Established | 2000 |
| Annual Output Value | US$5 Million - US$10 Million |
| Main Markets | Domestic Market, South Asia, Southern Europe, Northern Europe, Central America |
| Company Certifications | ISO9001;IS014001 Certificate |
2. Manufacturer Certificates
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period |
3. Manufacturer Capability
| a) Trade Capacity | |
| Nearest Port | Qingdao Port |
| Export Percentage | |
| No.of Employees in Trade Department | 10-20 People |
| Language Spoken: | English；Chinese； |
| b) Factory Information | |
| Factory Size: | Above 100,000 square meters |
| No. of Production Lines | Above 10 |
| Contract Manufacturing | Grinding Balls; Grinding Rods; Grinding Cylpebs. |
| Product Price Range | Average |
Send your message to us
Steel Grinding Media Mill Ball with Well Abrasive Resistance Top Quality For Cement and Mineral Processing
- Ref Price:
-
- Loading Port:
- Qingdao Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25MTS m.t.
- Supply Capability:
- 200000MTS/Year m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
