Small Home Portable Ice Maker Outdoor Party Camping Ice Maker

Add to Cart

Place Order

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Portable Compact Ice Maker: Ideal for Parties, RVs, Camping Vacations and Boat Tours

Product size: 242×358×328mm

Outer box size: 378×360×373mm

N.W / G.W: 17.2 LBS (8kg) / 20.3 LBS (9kg)

Ice Capacity: 26lb (12kg) / 24h

Water tank capacity: 2.2L

Ice basket capacity: 0.7kg

Rated current: 1.7A

Refrigerant: R600a 0.81oz/23g

2 different ice sizes: small, large

Make ice cubes in 6-13 minutes

Ice shape: bullet ice

Number of ice cubes per cycle: 9

Q:When ice making mechanism shows low water level and can't make ice, what's the matter?: Look, what ice machine do you use, the ice ice?

Q:Ice machine to remove ice time is short, resulting in ice can not fall off, and then began to ice, using a computer board control, did not find any adjustment ice thickness: The machines are spray type.The two - way solenoid valve with ice is combined with running water,

Q:Honeymoon dessert in the ice sheet for what to do?: Ice making machine: ice machine (English Name: ice maker or ice machine) is a kind of refrigeration equipment of water through the evaporator by refrigerant cooling system after the formation of ice, the refrigeration system using water carrier, while it is energized by a device made of ice.

Q:How to judge ice maker fault quickly: Failure occurred in the refrigeration system, in general can not directly see the fault location where they occur, it is impossible to refrigeration system components to decomposition and anatomy, check only from the outside, to find out the abnormal phenomenon in operation, were analyzed. During the inspection, generally by watching, listening and touching to understand the operational status of the system the operation of the system. When the pressure and temperature is higher than the normal range, in addition to the interior

Q:The missile like filter, with a water inlet or a water inlet? The release of water is black, doubt and water inlet wrong, to swim: You said the brand of the machine I have not seen, but I have seen a variety of ice maker, will not appear water intake and water outlet can not be separated. Water intake is generally better, brands are using electromagnetic valves to control water intake, bad brands rely on floater to control the amount of water, and the water does not control the water out of the device.

Q:The first ice making is normal. After the ice removal, the second time no ice making, what's the matter?: . 5, condenser is dirty, high voltage protection. Two, ice production reduced by 1, capillary or expansion valve plug. 2, the system moisture is too high, there is a slight ice jam. 3, ice machine condensation system is blocked. 4 lack of refrigerant or leakage. 5 、 the evaporator is dirty. Three, wet Bing Bing film is not hard, 1, environmental temperature is too high, especially in the summer will have a kind of situation. The machine repaired 2, add refrigerant. 3, ice separator water supply is too large. 4, press power shortage. Four, the machine running, but not out of ice, 1, water disk water is not enough or anhydrous. 2, reducer failure or deceleration motor. 3, system failure, ice jam. Dirty block, etc.

Q:Do you make ice? I have too little ice in the ice making mechanism.. Seek expert advice! Thank you: The 2 solution: 1. Lean the ice thickness properly, so that your daily ice is still so much, but there are more ice cubes. 2. Change the machine or add one.

Q:What is the principle of air cooling and water cooling in an ice maker?: Like a car engine, the cylinder is made of double layers and the middle part is carried away by circulating water, which is called water cooling.

Q:Ice machine usually how to maintain?: Cleaning, the use of vacuum cleaners, brush and other cleaning surface condensation of oil and dust, can not use sharp metal tools to clean, so as not to damage the condenser. Keep ventilation smooth. The ice maker must unscrew the intake hose head at two months,

Q:What do ER1 blinks mean by an ice maker?: If the resistance is above 27K, the controller is judged to be bad. It should be replaced. If the resistance is lower than 27K, any one of the two wires must be broken. The resistance is adjusted from 27K to 28K by series connection of resistors

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range