QM16160 ACCU-LOCK MACHINE VICE WITHOUT SWIVEL BASE
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
We are a specialized company for machine vises , whoseproducts are exported to Europe and America as well as developed countries .Wehave Q12,Q13,Q41,QM,QMN series .All the products have high precision ,and reasonabledesigns and reach the JB/T2329-11 standards .
Weare insisting that the quality is first and reputation is the best. We refocusing on our quality and innovation , We are looking forward to havingopportunities to set up more business relations with customers from all overthe word and establish the long-term cooperation with best products and perfectafter-service.
QM Series MachineVice
Performance and character:
1. It is one of main attachmentsfor milling、drillingmachine ,it is particularly suitable for the finishing of precision parts.
2. The accuracy of vice (parallelismand squareness) is 0.025mm/100mm.
3. The special segment in themovable jaw forces the vertical pressure downward when the horizontal pressureworks, so that this jaw does not lift the work piece.
4. Four positions allow extracapacity to change opening of jaw.
- Q: What does mechanical forceps mean?
- The main use of the clamp clamp is to underline, sawing, filing, drilling, reaming, tapping, thread and so on.
- Q: What's the difference between a vice and a vice
- Note to the pincers: (1) the machined surface of the workpiece must be higher than the tongs, otherwise it shall be made of a parallel mat. (2) to prevent the workpiece from being loose when the workpiece is loose in order to hold the clamp firmly, it must be applied to the iron and tongs. To make a workpiece stick close on the pad iron should be a clamp, a hammer tap the workpiece surface, smooth plane to knock knock to prevent injury by copper bar is bright and clean surface.
- Q: Common production desk vice, 45 # steel make the clamp plate, how to make pattern
- 45 # steel jaw plate, heat treatment at 860 ℃ quenching, quenching oil cooling water, 500 ℃ tempering hardness in HB300-350, can satisfy the requirement of general hardness and toughness.
- Q: How to draw a vice assembly drawing
- Draw a secondary structure. Check the proofs and revise the supplement.
- Q: What is the commonly used workpiece in milling machine
- Correct and reasonable use of vice, can not only ensure the positioning precision of the clamping workpiece, but also can keep the accuracy of flat vice itself, prolong its service life. When using the pincers, the following points should be noted: 1) clean and clean shavings and oil, and keep the tongs of the vise. 2) maintain a fixed clamp and adjust it to the correct position on the workbench. In order to make the clamping reliable, make the work of the workpiece with the clamping surface area larger, the workpiece which is short in the width of the tongs is as possible as possible in the middle part:. 4) it is not too much for the clamps to be installed, and the pincers should be added at the mouth of the tongs, as shown in figure 6-8, when necessary. In the case of a long working unit, two or more parallel jaw vice is available to keep the clamp tight and prevent vibration when cutting. 6) to the root
- Q: What is mechanical vice material
- Cast steel!The price is also higher。I hope my answer will help you。
- Q: Several basic USES of bench vice
- Installed on the bench, the width of the tongs is the calibration specification. Common specifications range from 75mm to 300mm.
- Q: Is the thread of a vice with a zigzag thread
- So don't generalize! The truth is the combination of theory.I hope my answer will help you
- Q: What is the use of the screw on the pincers of the flat slot with two orifices
- Screw holes for fixed vips, or reserved holes。I hope my answer will help you.
- Q: The difference between bench vice and vice! ~! ??
- he feature is that there is no chopping on the work surface, the accuracy is higher than the bench clamp, the function is similar to the tongs, and they are all the same.
Send your message to us
QM16160 ACCU-LOCK MACHINE VICE WITHOUT SWIVEL BASE
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
