Ceramic Filter Plate PP Film Faced MDF Board for Furniture
- Ref Price:
-
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 900 m.t.
- Supply Capability:
- 10000 m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
PP decorative foil is a kind of environmental protection material which is made by raw material of Polypropylene.
1.PP decorative foil doesn't include metal harmful substance , no harmful material is release while burning.
2.Visual sense of painted pattern(solid color and wood grain) on PP decorative film is really true to life.
3. Surface of the foil has function of stain resistance and electrostatic prevention.
4.PP decorative foil has function of flat press, vacuum press, module press, and special shape coat press.
5. PP foil passes through SGS test concerning the EU REACH.
6,can be used to the calcium silicate board , Mgo board , MDF, plywood ,and
aluminium sheet etc…
7,PP film size : Width: 1.25 m b. Thickness: 0.14mm
PP film laminated MDF board . It is a newly EP ( Environmental protection ) material , which are widely used in hotels , commercial clubs , home decoration , Engineering Design , interior trim ,Cabinet wardrobe ,high grade Product display counter etc..
melamine faced mdf board 25mm:
1)Standard size:1220x2440mm
2)Thickness: 2.0~30mm
3)Density: 730~830kg/m3
4)Glue: E2, E1.
Since MDF looks attractive with a fresh coat of paint or wood veneer, it is common material around the homes, offices, schools and hotels such as kitchen cabinets, office desk, flooring, furniture construction, shelving & bookcases, shop fittings, wardrobes and framing etc
- Q: Is the filter plate of the ceramic filter afraid of freezing?
- In addition, the temperature is one of the factors affecting the filter suction effect of ceramic filter. The lower the temperature, the worse the suction effect.Therefore, the ceramic filter plate, especially the ceramic filter plate after use, should be protected under low temperature environment.
- Q: Working principle, ultrasonic trouble and troubleshooting of ceramic filter
- It is based on the action principle of capillary pore and realizes the solid-liquid separation through the capillary action principle of the micropore. Specifically, is the use of microporous ceramic plate water impermeable properties, extraction of ceramic plate and external cavity vacuum pressure, the suspended material groove under the action of the negative pressure adsorption on the ceramic plate, solid material through the porous ceramic plate can not be trapped in a ceramic plate surface, and the liquid due to the hydrophilic effect of vacuum pressure difference and ceramic plate by entering the gas-liquid distribution device, and then discharged or recycled, so as to achieve the purpose of solid-liquid separation.
- Q: What is the filtration accuracy of 50nm ceramic membrane?
- It should be noted that due to wear, plugging and so on, the new and different degrees of ceramic film, the pore size will change. Micron scale ceramic membrane filtration accuracy is very good, nano scale aperture range of such a small ceramic film does not know in what way.
- Q: Can the plate filter press pass through the filter plate?
- Specific, it is necessary to choose the filter characteristics according to different materials. Plate and frame filter press: plate and frame filter press is an industrial realization of solid, liquid separation, plate and frame filter press is suspension, liquid-solid, liquid two phase, applied to chemical, ceramics, oil
- Q: What is the working pressure of the ceramic filter?
- The backwash pressure is the size of the backwash of the ceramic filter during recoil stage, and the recoil pressure is generally less than 0.12MPa. The greater the pressure, the better the recoil effect, the better the service life and the suction effect of the ceramic filter plate, and the worse the service life and the suction effect of the ceramic filter board. The backwash pressure of the ceramic filter shall be no less than 0.07MPa.
- Q: What is the reason that the ceramic filter does not absorb mineral powder?
- There may be a fault filtrate pump, diaphragm pump damage, pump mechanical seal failure, a leak, two is no output or output to the liquid, the pressure is too low, the cleaning effect is not good, the pressure is too large, will cause damage and reduce the concentration of slurry filter plate.
- Q: How can I avoid the backwash pressure in the production of ceramic filter?
- The backwashing system of ceramic filter is usually made up of water inlet, water inlet, pressure gauge, water filter and filtered water pressure gauge, and then connected to the inside of ceramic filter. Such as the discovery of ceramic filter recoil pressure became smaller or even no recoil pressure, you can carefully observe the surface of the ceramic filter plate is wet or ceramic filter plate wear without water injection at the discharge point, investigation and the reasons for the following aspects:Is the water inlet pressure or normal?How about the sealing performance of the water filter? Does the filter element need to be replaced?Is the recoil system piping (metal pipe, ceramic filter plate, connecting pipe, etc.) broken, leaking or dripping?Is the distributor valve properly installed and is it worn?Are there any cracks in the ceramic filter plate?Is the pressure gauge broken?The most likely reason is 1, 2, two, the best water should not be too dirty, filter should be replaced regularly. I hope the answer can help you.
- Q: Excuse me, what's the reason that all ceramic filters do not attract ore?
- After the joint cleaning, 0~2 hours of suction effect may be good, 2~4 may drop slightly, 4 hours later will become worse and worse, or even suck. This case should first check the backwash water pressure (instantaneous maximum pressure should not be less than 0.08MPa) is to meet the requirements, should also advance down (to ensure normal and ultrasonic cleaning combined with nitric acid dosage sufficient) and prolong the cleaning time.
- Q: Beneficiation ceramic filter no problem, the technical parameters are normal, but filter out the concentrate water suddenly excessive, what is the reason?
- The ceramic filter ceramic plate ceramic microporous pumping vacuum adsorption concentrate filtration water, the adsorption parameters according to the angle of rotation, reverse cleaning process, check whether there are loopholes in the exhaust pipe, check the ceramic plate use cycle is too long.
- Q: How to determine the quality of ceramic fiber filter board simply?
- Ceramic fiber board quality can be judged from the following aspects:1, appearance. The surface is flat and the cutting surface is well arranged, and vice versa.2 density. Press the hands, and the surface is soft and smooth.3, process. Vacuum suction and continuous production process.4, cross section, slag ball content is low.
Send your message to us
Ceramic Filter Plate PP Film Faced MDF Board for Furniture
- Ref Price:
-
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 900 m.t.
- Supply Capability:
- 10000 m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
