PE Plastic Sheet Foam Extrusion Machine Line

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

plastic sheet extrusion machine production line , pvc board production line , pvc decoration sheet production line

plastic sheet extrusion machine production line , pvc board production line , pvc decoration sheet production line

The plastic plate and sheet extrusion line is specially designed for the extrusion of single layer or multi-layer plate and sheef of PC or PMMA. It is also suitable for the sheet extrusion of PE , PP, PS, ABS and other materials.
The international famous components, combined with decades of year’s experience in the plastic machinery industry, make the whole production line more perfect, reliable and steady.

model	GWP120/21	GWC80/156-1220
products width(mm)	1400	1220
products thickness	0.3-1.5	0.5-3
extruder specification	GWP120/21	GWC80/156
Main motor power(KW)	90	75
Designed extrusion output(KG/H)	350	300

plastic sheet extrusion machine production line

PE Plastic Sheet Foam Extrusion Machine Line

Q: For example, 70 square conductors, the outer diameter is A, out of the insulation, then the line mouth to choose how much, how much plastic cover election? Then the sheath, then how to choose the mold?: Depending on your specific specifications, if XLPE is insulated, extrusion die with small touch line, set on the use of cable diameter, large core conductor than a few tenths of good, if you like to use 70 square tube extruding mold insulation of the conductor element some is big 1 can be set according to the touch, the tensile ratio calculation,

Q: extrusion machine prone to coke material, what is the cause? How to improve or solve?: Is the place where the material is easy to burn rough? Add stabilizers and lubricants appropriately. Or the outer lubrication part of low molecular weight is replaced by macromolecule lubrication

Q: Cable extrusion machine 6.57090 machine model how to see, know the master to say, thank you: Cable extruder type 657090 machine, describes the diameter of the screw, the unit is mm.The greater the number, the greater the equipment, the greater the amount of gumIt is usually marked on the control cabinet of the equipment

Q: Can PC and PP be extruded together with two materials in an extruder?: No co extrusion, PC polycarbonate, PP polypropylene, two kinds of product structure is not the same, not the same chemical composition, viscosity and liquidity is not the same, processing temperature and processing technology is also very different, and two kinds of products, so not incompatible, CO extrusion.

Q: What is the adjustment method of China's extrusion machine die?: (3) line to die: suitable for small section of wire and cable adjustment. Pass the wire through the mold core, connect to the traction line, then run the glue and fine tune it. When the glue is running, adjust the screw and the traction speed, start the car, take the line sampling, and then stop to observe the thickness of the plastic layer of the sample is even, repeated several times until the tune until so, and then tighten the screws

Q: Cable extruder how to match the mold, how to calculate the formula, ask the master pointing: Look at what you have in the form of mold, extrusion, drawing, or half pipe

Q: Why single screw extruder is controlled by high school and low?: I feel like I didn't explain the problem

Q: Where is the Huangyan extruder machine?: You want to see what type of mold processing, but Masino comprehensive, injection mold, blow mold, mold and so on can be developed.

Q: There is a 90 extrusion machine, used in the production of communication cables (outside the cable core is extruded with a layer of LLDPE), now is the configuration of Y2-280M-490KW167A inverter type ACS510197A + ABB), General Motors now found low speed when the current is too large, what reason? How to solve? The details are as follows: used for communication cable production HYA30*2*0.4, 1, line speed is 50 m / min, inverter display frequency 35.3HZ current: 116A; 2, line speed is 40 m / min, inverter display frequency of 28.2hz, current: 140A3, line speed is 35 m / min, the frequency converter significantly method: 157A 24.6HZ frequency current, because the product variety and technical reasons, we need to be in the frequency of 10HZ production. Now, it seems that if I reduce the speed again, the current will probably exceed the rated current. What should I do? Is the motor changed to frequency conversion motor? Or inverter? How to solve? Please heroes pointing, thank you!: Fan, water pump at low speed, torque is not enough, resulting in high current, if vector control can be ideal.

Q: why production is not strong?I have several new co extrusion machines, but the blown plastic bags are not produced by others: Plastic tensile testing without tension is strong that said, you should be the low tensile strength, tensile strength for 2 kinds of films, one is the transverse tensile strength, a longitudinal tensile strength, is a reflection of the tensile properties, the tensile strength of the plastic bag if you low, because your choice of materials is not brittle material or toughness (PE/PP/PVC/PET/PBT/PC do not know or what material) if you insist on using this material, make plastic bags, you can modification method by crosslinking, adding additives, improving formula, to achieve the goal, the specific situation you need to find a degree in Polymer Science plastic engineer, they will tell you.

Send your message to us

*Email

*TEL

*Quantity

*Unit