Electrical threading PVC conduit pipe production line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Electrical threading PVC conduit pipe production line
PVC double pipes production line Description:
The pvc groove extrusion line is equipped with conical double screw extruder.
With this machine, the line can achieve a high-efficient production.
PVC double pipes production line Application:
The final products are widely used in protecting wires and cables in daily life or industry and construction.
It has the advantages of wear-resisting and moisture proof so it can make wires and cables safe.
PVC double pipes production line Process flow:
Raw material+additive→mixing → conveying feeding → force feeding → conical double screw extruder → "one mould two pipes"mould → calibrator → double spray vacuum calibration tank → ink printer → double belt haul-off → double uplift cutter → double pipe rack → finished product inspecting&packing
PVC double pipes production line Technical parameters:
Model | Screw diameter | L/D | Pipe range | Capacity | Main motor power | Total power | Line length |
U-PVC40 | 51/105mm | 14.5:1 | 16-40mm | 80-120kg/h | 18.5kw | 50kw | 22m |
U-PVC63 | 65/132mm | 14.6:1 | 16-63mm | 120-250kg/h | 37kw | 100kw | 25m |
- Q: Why is the connection between the extruder and the switchboard?. The upper and lower three terminals are short circuited
- The action should be to require three simultaneous electricalOr a two way backup
- Q: Produce 10 square wires with the smallest extruder
- If the production of single core line, then 50 machines can also do, but low efficiency, unstable line,.70 or 90 machine idealIf it is a production sheath line, do at least 70 machines, preferably 70 or 90 insulation, and 90/120 as sheath
- Q: Plastic double screw extruder, pumping air will accumulate material, how is it going on?
- Adjust the assembly and check the exhaust block
- Q: Can PC and PP be extruded together with two materials in an extruder?
- No co extrusion, PC polycarbonate, PP polypropylene, two kinds of product structure is not the same, not the same chemical composition, viscosity and liquidity is not the same, processing temperature and processing technology is also very different, and two kinds of products, so not incompatible, CO extrusion.
- Q: 1: what is the difference between an extruder and an injection molding machine?Answer the questions in terms of structure, process, product difference, material distinction, mould distinction and development areaThis is a kind of mechanical professional mold mold equipment on an essay question, please the professional teacher to help answer, thank you very much, the students have urgent need, thank you!!
- 2: injection molding machine, mainly to melt the plastic injection molding process, after the mold injection molding machine outjection. The main products are mechanical parts, containers, household appliances shell.
- Q: Comparison of injection molding machines and Extruders
- Considerations for extruder use:1, extrusion machine is running forward, avoid reverse2, avoid fasting operation, must heat engine feeding operation, so that can avoid sticking bar (holding shaft) phenomenon3, the extruder inlet, vent hole is strictly prohibited access to iron and other miscellaneous, so as not to cause accidents, affect production4, safe use of electricity, grounding wire5. When the machine is running, it is forbidden to touch the rotating parts such as the material inlet, the material outlet, the belt, the gear and so on6, before using the machine should be injected with lubricating oil, so as not to cause damage to the machineSince the extruder as one of the three synthetic plastic material since the advent of rapid development.
- Q: What is the temperature setting of the extruder and how much is the setting temperature of the head and filter?,
- Setting the temperature completely depends on the actual situation.Generally, the position of the leaky hopper is lower than the temperature of the extruder barrel and the die head
- Q: Why single screw extruder is controlled by high school and low?
- I feel like I didn't explain the problem
- Q: Taper twin screw extrusion machining of plastic masterbatch? What ancillary equipment do you need?
- Can, but need feeding machine and related auxiliary mixing granulator, the cost is not low, but the effect is less than double make flat,
- Q: What are the components of an extruder?
- The driving system of an extruder is to drive the screw, providing the torque and speed required by the screw in the extrusion process, usually consisting of an electric motor, a reducer, and a bearing.3. heating and cooling device for extruderHeating and cooling are necessary conditions for the process of making a plastic extruder. It includes two aspects:(1) now host extruder is usually divided into electric heating, resistance heating and induction heating, heating installed in the fuselage, neck, head of each part. The heating device heats the plastic in the outer barrel to increase the temperature required for the process operation.(2) the cooling device is designed to ensure that the plastic is in the temperature range required by the process. Specifically, to eliminate the excess heat generated by the shear friction of the screw rotation, in order to avoid the temperature is too high, so that plastic decomposition, coke burning or stereotypes difficult. Cylinder cooling water cooling and air cooling is divided into two kinds, small and medium sized extrusion machine adopts air cooling is more appropriate, large use more water or two kinds of combined cooling; cooling water cooling screw mainly adopts the center, the purpose is to increase the solids conveying rate, stable glue volume, and improve product quality; but in the cooling hopper one is, in order to strengthen transport of solid material, prevent warming plastic sticky jam outlet, two is to ensure the normal work of the transmission part.
Send your message to us
Electrical threading PVC conduit pipe production line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
