PVC skinning foam board extrusion production line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
PVC skinning foam board extrusion line
1.Raw material:PP/PE/PVC(can use recycled plastic)+wood/rice husk powder
2.Final product: decking, garden railing, garden furniture, wall cladding, pallet, garden deck.
window and door,furniture board, ceilling panel, wall siding panel, flooring, partition wall.
3. PVC skinning foam board extrusion line final products:
PVC foam plate/sheet/board, PVC expansion sheet/board/plate
4. PVC skinning foam board extrusion line products properties and application:
WPC foam board machine/PVC WPC foam board machine brief introduction | The PVC foam board is made through foaming and pressing into shape with additive. It is widely used in sanitaryware, construction material and advertising material.
|
PVC crust/skinning foam plate/sheet/board properties | 1.Waterproofing 2.Fire retardant and self-extinguishing. 3.Heat preservation 4.Sound-insulated 5.Anticorrosion and antitoxic 6.Tough, rigid with the high impact strength 7.Stable color retention |
PVC crust/skinning foam plate/sheet/board applications | 1.Building outdoor wall board, indoor decoration board, partition board in office and house 2.Screen printing, flat solvent printing, engraving, billboard and exhibition display 3.Chemical anticorrosion project, special cold project, environmental protection |
PVC crust/skinning foam plate/sheet/board specifications | 1.Thickness (mm): 1 – 25mm 2.Width (mm): 1220, 1560, 2050 3.Length (mm): 2440, 3050, 6000 4.Density: from 0.5 to 0.8 5.Color: white, black, red, blue, yellow, green, gray |
5. PVC skinning foam board extrusion line main constitute:
Item | Qty |
Hot-cooling mixer | 1set |
Conical double screw extruder | 1set |
Conical double screw co-extruder | 1set |
Forming mould | 1set |
Cooling rolls | 1set |
Hauling machine | 1set |
Cutting machine | 1set |
Stacker | 1set |
6. PVC skinning foam board extrusion line main technical parameter:
Main extruder and motor | Conical double screw extruder 75kw |
Co-extruder and motor | Conical double screw extruder 37kw |
Cooling roller | stainless steel |
Haul-off machine | Multi-roller haul-off machine |
Cutting machine | 2.2kw |
output | 450kg/h |
Feeding motor | 1.5kw |
7.Main technical information of PVC skinning foam board extrusion line
Model | CCMS-180
| CCMS-240 | CCMS-300 |
Profile Max Width | 180mm
| 240mm | 300mm |
Extruder Model | SJSZ-55/110
| SJSZ-65/132 | SJSZ-80/156 |
Vacuum Table Length | 4000mm
| 6000mm | 6000mm |
Output(max) |
150kg/hour | 250kg/hour | 380kg/hour |
- Q: For example, 70 square conductors, the outer diameter is A, out of the insulation, then the line mouth to choose how much, how much plastic cover election? Then the sheath, then how to choose the mold?
- Depending on your specific specifications, if XLPE is insulated, extrusion die with small touch line, set on the use of cable diameter, large core conductor than a few tenths of good, if you like to use 70 square tube extruding mold insulation of the conductor element some is big 1 can be set according to the touch, the tensile ratio calculation, PVC1.6 DYWL material with smaller good-looking it is simple of the extrusion process
- Q: extrusion machine prone to coke material, what is the cause? How to improve or solve?
- Or the outer lubrication part of low molecular weight is replaced by macromolecule lubrication
- Q: Extrusion blow molding machine, storage or continuous type good?
- The amount of extrusion must be continuous, efficient, and wasteful
- Q: Which type of inverter is suitable for extruding machine? Please give expert advice, and G series is discontinued
- Proposed Delta VFD-cp Series ~!AskCP2000 is constant pressure water supply... Are you sure you can use it? And C2000 is better than qualifiedChasing the answerWrong number ~ ~ should be C2000, and VE Series ~ ~ these two are suitable, ~~B, CP is not good ~!
- Q: Before and after the original good tune, up and down again before and after the tune, before and after, and up and down again
- The nose is not accurate enough or wornOr the screws are not screwed in placeOr die inappropriate, too large
- Q: Extrusion machine operating procedures, specific points, thank you!
- 6, the speed from low to high, added to the normal speed, is strictly prohibited high-speed car, observe the instrument on the current value and temperature is normal, in case the current is too large, cause the heater to burn.7, when lifting the disk, we should pay attention to the limit of the rise and fall, not too high or too low, when there is an electrical limit, shall not exceed the limit.8 when feeding to the hopper, be careful not to enter the metal, and do not use a screwdriver or a metal bar to poke the plastic into the screw.9 check the dry test machine, should be equipped with rubber insulation plate, otherwise, no driving.10 before driving, should check whether the ground location is good, grounding resistance should be measured regularly, not higher than 4 Europe; equipment whether there is noise and other anomalies, if there is a problem, repair and reuse.
- Q: Taper twin screw extrusion machining of plastic masterbatch? What ancillary equipment do you need?
- because itself is not suitable for the design of double cone, adjustment of the formula is the key.
- Q: How to adjust the 65 screw gap in the extruder?
- This should be practical learning. The outlet plane of the barrel is about 3 mm in diameter.
- Q: Is the extruder the same as the extruder?
- The extruder is also called in the screw extruder is under the action of the molten plastic extrusion through fixed shape extrusion, water cooling after cutting in the traction machine under the same section is mainly used for a variety of products.
- Q: Who knows the temperature regulation method of the extruder?Any information will do
- 1, extrusion methodAccording to plasticizing methods: dry extrusion and wet extrusionPress the way: continuous extrusion and intermittent extrusion2, characteristicsContinuous production, high efficiency, simple operation, wide range of applications [Edit] paragraph extrusion molding equipment 1, the hostExtrusion system: composed of screw and barrel, it is the key part of extruder. Its function is to melt plastics, quantitative, constant pressure, constant temperature extrusion of meltDrive system: drive the screw to increase the required torque and torqueHeating and cooling system: guarantee the temperature of plastic and extrusion system in molding process2 auxiliariesIt is composed of head, setting device, cooling device, traction device, coiling device and cutting3 、 control systemIt consists of electric apparatus, instrument and actuating mechanismPurpose: to control the main and auxiliary motor, in order to meet the demands of speed and power; control main engine temperature and pressure and flow, to ensure product quality; to achieve automatic control of the extrusion unit, ensure the coordinated operation of main and auxiliary equipment. [edit this paragraph] extruder extruder overview of plastic extruder is the host, it consists of extrusion system, transmission system and the heating and cooling system.
Send your message to us
PVC skinning foam board extrusion production line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
