Marine Horizontal Self-priming Centrifugal Pumps
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 4000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Introduction
JSP/JSW series are suitable for pumping clean water. They are particularly suitable for domestic applications such as supply water from well, pool etc, the automatic distribution of water by surge tanks and pressure switch, gardening, and increasing of water pressure.
2.Features
a.JSP/JSW Series pump is constituted with clean water pump, non-return valve and air-water separation room, which located on the upside of the pump body.
b.During operating, it is no need to use foot valve, the only thing that you should do is just leave some water in the pump body.
c.After a few minutes' running, the water will be sucked out relying on the pump body itself.
d.They are particularly suitable for domestic applications such as supplying water from well, pool etc.
e. It is also suitable for water pressure boosting, gardening and automatic water supplying if combined with other appliances.
3. Construction
Pump Body: Cast Iron/Stainless Steel/Brass Front Cover: Cast Iron/Cast Iron with brass insert / Aluminum / Brass Impeller: Brass/Aluminum/PPO Mechanical Seal: Carbon/Ceramic/Stainless Steel Motor Housing: Alloy Aluminum Shaft: Carbon Steel/Stainless Steel/High Frequency Wedding Shaft Insulation: Class B / Class F Protection: IP44 / IP54 Cooling: External Ventilation
With thermal overload protector in single phase motor
4. Working Conditions
Max Temperature of Fluid to +80C
Max Pressure 10bar
Max Ambient Tenperature up to 40C
- Q: What are the general water pump failure, how to repair?
- Troubleshooting of water pumpFirst, the water pump does not cause water analysisThere is air in the inlet pipe and pump body(1) before the water pump is started, the water is not filled enough. Sometimes it seems that the water has been discharged from the vent hole, but the pump shaft is not rotated. The air is completely discharged, resulting in a small amount of air remaining in the inlet pipe or pump body.
- Q: Variable flow pumps are variable pumps
- To be exact, variable pump means variable displacement. Because if the displacement does not change
- Q: What is the "variable" of a variable pump? Is the displacement change or the flow change? Thank you
- These two don't mean the same thing? That is, the pump outlet can be changed
- Q: What is the lift off the dead center point? This is a straight mark about the water pump. What is the function and the relationship between the design head and the pump head? ThanksWhat exactly is the dead point lift? What's the function of this indicator?
- Pump downstream equipment design pressure is greater than 3MPa, if it is 400 meters, the downstream equipment design pressure is greater than 4MPa
- Q: How many kilograms of water pump are there in the automatic washing machine on the market?
- Longer service life. Automatic switch water pump, car wash automatically open and stop, easy to operate, not easy to bad, repair rate is low!!!
- Q: Water pump does not produce water, what are the reasons?
- The reason why centrifugal pump does not produce water:1. pump inlet or sink, water tank water shortage.2. water pump pipe blocked or valve not open.
- Q: Please give me professionals to calculate, the cylinder bore is 100 and the rate of 20m/s, the leakage can be ignored, but to the large flow pump!
- Select the hydraulic pump from the following considerations:1. hydraulic pump pressureHydraulic pump operating pressure is the pump (or motor) in actual work output (or input) oil pressure, determined by the external load.Rated pressure refers to the maximum pressure under continuous running in accordance with the test standards under normal working conditions. The size of the pump is limited by the service life, and the service life of the pump (or motor) will be shorter than the design life if it exceeds the rated pressure. When the work pressure is greater than the rated pressure, it is called overload.
- Q: Working principle and structure of external gear pump
- External gear pump is the most widely used gear pump, the general gear pump usually refers to the external gear pump. Its structure as shown in the diagram, there are mainly driving gear, driven gear, pump body, pump cover and safety valve and so on. The seal space of pump body, pump cover and gear is the workshop of gear pump. The wheel shafts of the two gears are respectively arranged in the bearing holes on the two pump cover, and the driving gear shaft extends out of the pump body and is driven by the motor to rotate. The external gear pump is simple in structure, light in weight, low in cost, reliable in operation and wide in application. When the gear pump works, the driving wheel rotates with the motor and drives the driven wheel to rotate
- Q: Why can't the centrifugal pump pump the vacuum?
- Condition:The pump shell must be filled with liquid under certain installation height and running without leakage.What is the phenomenon of centrifugal pump? What harm does it have? How to eliminate?)
- Q: What's the submersible pump?What is a submersible pump, and what about it?
- Not afraid of water, because it is placed in the water itself to cool themselves, you can use for a long time. The amount of water pumped and the height of the water now basically meets the needs of a small amount of individual and a large number of factories. This is the submersible pump, the water pump in the water. You can see.
Send your message to us
Marine Horizontal Self-priming Centrifugal Pumps
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 4000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
