Roofing Insulation for Shop Walls - Heating Insulation and Fire-Proof Rock Wool Board
- Ref Price:
-
$5.00 - 10.00
/ m²
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 m²
- Supply Capability:
- 1000000000 m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Heating Insulation and Fire-proof Rock Wool Board
1.Structure of Heating Insulation and Fire-proof Rock Wool Board：
Rock wool insulation refers to a type of insulation that is made from actual rocks and minerals. It also goes by the names of stone wool insulation, mineral wool insulation, or slag wool insulation. A wide range of products can be made from rock wool, due to its excellent ability to block sound and heat. This type of insulation is commonly used in building construction, industrial plants, and in automotive applications.
The Manufacturing Process
Melting / Forming into fibers /Continuous-filament process/Staple-fiber process/ Chopped fiber/ Rock wool / Protective coatings /Forming into shapes
2.Main Features of Heating Insulation and Fire-proof Rock Wool Board：
● FEATURES
Thermal Insulation
Fire Safety
Acoustic Control
No Corrosion
Environmental friendly
Moisture Resistance
Energy Conservation & Emissions Reduction
Different raw material: Our rock wool is mainly made by Basalt and other natural ores. The raw material for other so-called rock wool is mineral slag. Different raw material, different features.
Different corrosion resistance. Our rock wool have good corrosion resistance. non-corrosive for metal. But the mineral slag wool is different. In high humidity environment, CaS in mineral slag will have chemical reactions and produce corrosive when contact with metal.
Different working life. The working life for mineral slag is very short and Durability is very low because of higher CaO and MgO in slag. The efflorescence for mineral Slag is easy and also effect the working life. The
Different heat resisting. The heat resisting for rock wool(Basalt) is higher than mineral Slag wool. Our operating temperature can reach 800℃.But for Slag wool ,can not higher than 675℃.The features for our rock wool is totally superior to Slag wool.
3. Heating Insulation and Fire-proof Rock Wool Board Images
4. Heating Insulation and Fire-proof Rock Wool Board Specification
ROCK WOOL BLANKET & BOARD
Standard Size
Product Blanket Board
Density (kg/m3) 60-100 40-200
Size: L x W (mm) 1200X3000-6000 600X1200
Thickness (mm) 30-150 30-100
Remark:
Other sizes are available upon request.
Facing materials can be applied upon request.
Standard Size
Product Blanket Board
Density (kg/m3) 60-100 40-200
Size: L x W (mm) 1200X3000-6000 600X1200
Thickness (mm) 30-150 30-100
Remark:
Other sizes are available upon request.
Facing materials can be applied upon request.
Rock wool PIPE
Standard Size
DIA Thickness (mm)
inch mm 25 30 40 50 60 70 80 90 100 120 150
1/2’’ 22 ● ● ●
3/4’’ 27 ● ● ● ● ● ● ●
1’’ 34 ● ● ● ● ● ● ●
1-1/4’’ 43 ● ● ● ● ● ● ● ● ●
1-1/2’’ 48 ● ● ● ● ● ● ● ● ●
2’’ 60 ● ● ● ● ● ● ● ● ●
2-1/2’’ 76 ● ● ● ● ● ● ● ● ●
3’’ 89 ● ● ● ● ● ● ● ● ●
3-1/2’’ 108 ● ● ● ● ● ● ● ● ●
4’’ 114 ● ● ● ● ● ● ● ● ● ●
5’’ 140 ● ● ● ● ● ● ● ● ● ●
6’’ 169 ● ● ● ● ● ● ● ● ● ●
8’’ 219 ● ● ● ● ● ● ● ● ●
10’’ 273 ● ● ● ● ● ● ● ● ●
12’’ 325 ● ● ● ● ● ● ● ● ●
14’’ 356 ● ● ● ● ● ● ● ●
15’’ 381 ● ● ● ● ● ● ● ●
16’’ 406 ● ● ● ● ● ● ● ●
18’’ 456 ● ● ● ● ● ● ● ●
19’’ 483 ● ● ● ● ● ●
20’’ 508 ● ● ● ● ● ●
22’’ 558 ● ● ● ● ●
24’’ 610 ● ● ● ● ●
5.FAQ
We have organized several common questions for our clients，may help you sincerely：
① What’s the mainly material for rock wool？
Rock wool is called a mineral wool because it is made primarily from basalt, an igneous rock,
②What’s the mainly type for rock wool？
rock wool insulating products are available in loose-fill form and as batting. Batts, or blankets, are thick slabs of insulation that may have a kraft paper facing.
③How you control the quality?
During the production of fiberglass insulation, material is sampled at a number of locations in the process to maintain quality.
- Q: Our roof tile is installed on top of galvanized iron sheets. We do not have any toher form of insulation. The roof tile or tegula is quite thick.
- Oh yeah. You need insulation. Think of it this way. If you turned a stove top burner on medium-low and placed one of those roof tiles on it, it would be too hot to pick up. If you put down a small piece of insulation first, you'd be able to pick up the tile with no problem.
- Q: were can i buy material to insulate pans and instructions to install it? I have seen many roofs with this done ,but , the lowe,s and home depots don't have .
- I think your problem is in the way you are asking the question. I for one do not know what you mean by a metal pan roof. I know all about steel roofs or corrugated roofs and a lot of other roofs but what is a metal pan?
- Q: or in queensland
- Depends on whether you are employed or working contract. Currently it could be 18-25 per hr for employee or upto 40 per hr for contract depending on allowances and if you are providing your own vehicle or company vehicle. Then are you doing bats or anticon, it is usually charged on a sqm rate. Call some roofing companies or insulation companies and ask them what their rates are.
- Q: weather stripping/ foam strip?
- Those foam strips they sell you to go under the ridge caps will eventually dry out, blow out, and be hanging all over the place. Caulking won't fill a 5/8's gap to keep the wind/rain out, and tar has no place whatsoever on a metal roof, you'll get it all over everything, and either one will look like ****. The best ridge cap has to be custom made and cut to fit. I use a 12" wide X 10' strip, bent in half to pitch, and then turn down 90 degrees on the edges, whatever the rib height is, usually 5/8". Hold the ridge cap in place on the ridge and mark where the ribs are, then notch out for the ribs so that the cap sits flush over the ribs and down on the flats, punch holes and screw down thru the tops of the ribs. It's a little time consuming but it makes for a good looking finished product that won't wear out.
- Q: roof was replaced eight years ago soon after there were leaks in the roof caused insulation toget wet then dry now the insulation is packed hard and has started to turn into power who would be responsible to replace the insulation.
- Sorry; I don't know of any roofer that would take responsabilty after eight years. Unless your insurance might be an option. Check with them and decide if your deductable is more than the repair if you would be better off doing it yourself. I would also be concerned about underlying materials, sheet rock, lumber, MOLD. You need someone to check thoroughly for mold being as it has been so long. GOod luck; Flip;
- Q: I gutted the room and now would like to rebuild. One side of the room slants (it's the roof) and the other side of the room is a dormer (all low ceilings).I want to insulate the ceiling but have no ridge vents so no moving air as someone mentioned I should have. I want to install foam channels to keep the insulation away from the roof but not sure if this is a good idea without the ridge vents. I will have a vent to the outside installed on the very top of the roof however and the small attic space is open all the way through the other two upstairs rooms and I will add another roof vent on that end of the house. I will only be able to install 3 inch insulation but that's better than none at all. I live in the northeast and was told if the job isn't done right I can get ice jams in winter. Also I don't see any way to drill ridge vents. would it be ok to just install the styrofoam channels and insulate then sheet rock or am I asking for trouble? Thanks in advance for any help.
- Suggestion: install the insulation with the foam channels but leave the center section (roof ridge area) open from end to end. At each end you can install a static vent or an active one. Depending on the amount of space you have you may be able to install a power vent.If you can send me a diagram with measurements I can give you a more definitive answer.
- Q: I have a split house with an attic where I have insulation on attic floor, but the house seems to be cold still, Can I add insulation to the roof of the attic? If so, any options? Thank you.
- Most attics are vented, so I'm not sure how effective that would be.
- Q: The attic was converted into two rooms and I want to add insulation but the space between the ceiling of the rooms and the roof is about 5 inches? How should I do this?
- There are closed-cell expanding foam insulation materials that can be installed through rather small holes in the ceiling. The advantage of this material is that it also serves as a vapor-barrier - a critical function in your case. Not cheap, but very effective. Make sure you install roof vents to prevent excessive heat from developing above the insulation - but with foam, this requirement is far less onerous than with blown in or batt insulation.
- Q: What's better- to lay out roof insulation in an old house or to get it blown in?
- Blown in. It's better and also cheaper to have the insulation blown in. It's better because the insulation will go around wires, ductwork, and pipes much easier. It can get into nooks and crannys easier. It's much quicker also.
- Q: I am in the process of having a new roof installed. What are my options in regards to improving its' insulating properties?
- If you have clear access to your rafters, the best insulation possible (after installing your vent baffles) is sprayed on foam. I didn't say polyurethane foam on purpose, as there is now a soy based foam available with exactly the same working and thermal characteristics as the petro-poly goop, with none of crude oil. But i digress. Sprayed on foam has the advantage of not only thermal insulation but it also seals everything that it comes in contact with, thus stopping any air movement, something that no fiberglass or extruded polyurethane could ever do. Industry experts are still debating this but, it looks like 1 inch of sprayed on foam (with it sealing qualities) does as much, if not more, than 3 1/2 inches of fiberglass and, foam will never sag or absorb moisture like glass does. Fill your rafter spaces and gloat to the neighbors when your bills come in. :)
Send your message to us
Roofing Insulation for Shop Walls - Heating Insulation and Fire-Proof Rock Wool Board
- Ref Price:
-
$5.00 - 10.00
/ m²
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 m²
- Supply Capability:
- 1000000000 m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
