Fiberglass Gypsum Board 12.5mm Thick Glass Fiber Reinforced Gypsum Board

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Specification

Formaldehyde:

Q: hello I intend on insulating and plaster boarding my shed soon. However I am not entirely sure of the best way to plasterboard onto a metal frame, because I do not want screws poking out of the board because you cannot nail into metal obviously. So I was wondering do most people use only liquid nails or how else is the board applied to the frame? I heard you can put small pieces of wood between the frame and the board then nail to the wood, is this a good technique? advice and opinions would be much appreciated thanks: use bolts. plaster and paint over to hide them. get the rounded, covered nuts to go on the outside of the shed.

Q: What is the process of the gypsum board production line?: Forming section ?????? Formed paper by the paper machine, tensioning device, marking device, correction device sent to the forming station, gypsum slurry from the vertical mixer to the formation of paper on the next. Forming the paper machine by the paper machine, tensioning device, correction device and glue, sent to the molding station. Molding machine for the plate, the thickness can be adjusted. Molding machine on the paper, the next paper, gypsum slurry squeezed into the provisions of the thickness of the plate, a good gypsum board with a solidification belt conveyor belt conveyor conveyor belt sent to the cutting machine at the set length cut off, and then by the acceleration roller Road into the type 1 horizontal conveyor, by pushing the roller bed into the dryer.

Q: Gypsum board partition with what norms: 7, the installation of gypsum board should be from the middle of the board to the four sides of the plate fixed. The head slightly into the board 0.5 ~ 1.0mm, and shall not damage the paper. 8, gypsum board seams should be used to supply the supply of joints with seams and seams with joints. Gypsum board and the surrounding wall or column should be 3mm slot, in order to carry out cracking treatment. Note that can not be used full of putty instead of caulking putty. 9, the angle should be the angle of protection, vulnerable to the collision site of the sun angle should adopt the metal angle; non-vulnerable parts of the sun angle should be used metal corner paper tape.

Q: In Baoying County Jianxiang decorative materials set a total of approved materials, and then also please help me analyze the analysis of users!: There are two kinds of gypsum board; one is only decorated with ceiling - calcium calcium gypsum board.

Q: Gypsum board how much money a: The price is high and low, the general no-name card eight or nine dollars, the quality is not good, mid-range and some brand fame of the general seventeen eight to twenty-four five, upscale and with a certain function to forty or fifty, Ten.

Q: Gypsum board is toxic Gypsum board what ingredients for home decoration is toxic: Gypsum board with phosphogypsum contains harmful ingredients on the human body, the domestic Taishan gypsum board most of the use of phosphogypsum.

Q: I'm using these 'wall anchor' bolt things to hold stuff up on the wall. They're the ones that slot through a drilled hole and then when you tighten the screw in them, the part behind the wall gets compressed until it presses against the back of the wall. That's probably irrelevant though...These wall anchors are rated to hold 10kg when used in 10mm thick plasterboard walls. I'm using them in a fibro cement wall which is approx 6mm thick. Seeing as fibro cement walls are way stronger than plasterboard, would you have any idea what the wall anchors could support in them? 20kg? 30kg?I know this is going to be pretty hard to answer accurately, but any educated guesses would be great! Thanks: fibro cement may be stronger but i would guess it is more brittle too. it may crack when you tighten the anchors if you can find a couple of studs and screw directly to these it would help

Q: can you tile ceramic tiles on plasterboard?: Yes you can in non wet areas. Strongly not recommended in wet areas such as tubs and showers, Any questions you can e mail me through my avatar and check my qualifications there. GL

Q: What does Plasterboard look like?: Its a wooden window sill, plasterboard is what is on the wall bellow it, asbestos (to my knowledge) was never used as window sills, nor was used in place of plaster in old houses, or plaster board in new houses, it was used as roofing material on industrial buildings,

Q: What is the specification? What quality requirements?: The country's largest gypsum board production line, North New, with the Zaozhuang Tengzhou plateboard

Send your message to us

*Email

*TEL

*Quantity

*Unit