PE, PP, PVC And Wood Plate Extrusion Line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 30 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Packaging & Delivery
| Packaging Detail: | 1.wooden case 2.by requirements |
| Delivery Detail: | 65 days |
WPC extrison line:
It adopts special design of screw & barrel, mould and extruder for wood plastic products.CNBM company
products series:One step way thick board extrusion line,One step way WPC profile extrusion line;WPC pelletizing extrusion line and different kinds of WPC mould.
The WPC products can be produced by two step extrusion machine, or pelletzing first then through extrison machine, it will save power and place,it has some feature: high output,stable extrusion pressure,high plastication, and good mixing. Optimized screw design have small cutting strength, and it is not easy to cut wood fibre, good plastication.
This extrusion line can produce PE,PP or PVC WPC profile products,Main application is for wood tray, indoors and outdoors floor,and outside decoration,and so on.
Techinical parameters:
Product show:
All Key parts: screw&barrel,melt pump, screen changer, mold, and downstream equipment are made by Jwell factory!
- Q: For example, 70 square conductors, the outer diameter is A, out of the insulation, then the line mouth to choose how much, how much plastic cover election? Then the sheath, then how to choose the mold?
- Depending on your specific specifications, if XLPE is insulated, extrusion die with small touch line, set on the use of cable diameter, large core conductor than a few tenths of good, if you like to use 70 square tube extruding mold insulation of the conductor element some is big 1 can be set according to the touch, the tensile ratio calculation, PVC1.6 DYWL material with smaller good-looking it is simple of the extrusion process
- Q: Why is the connection between the extruder and the switchboard?. The upper and lower three terminals are short circuited
- The action should be to require three simultaneous electricalOr a two way backup
- Q: What is the adjustment method of China's extrusion machine die?
- (3) line to die: suitable for small section of wire and cable adjustment. Pass the wire through the mold core, connect to the traction line, then run the glue and fine tune it. When the glue is running, adjust the screw and the traction speed, start the car, take the line sampling, and then stop to observe the thickness of the plastic layer of the sample is even, repeated several times until the tune until so, and then tighten the screws
- Q: Comparison of injection molding machines and Extruders
- Considerations for extruder use:1, extrusion machine is running forward, avoid reverse2, avoid fasting operation, must heat engine feeding operation, so that can avoid sticking bar (holding shaft) phenomenon3, the extruder inlet, vent hole is strictly prohibited access to iron and other miscellaneous, so as not to cause accidents, affect production4, safe use of electricity, grounding wire5. When the machine is running, it is forbidden to touch the rotating parts such as the material inlet, the material outlet, the belt, the gear and so on6, before using the machine should be injected with lubricating oil, so as not to cause damage to the machineSince the extruder as one of the three synthetic plastic material since the advent of rapid development.
- Q: Before and after the original good tune, up and down again before and after the tune, before and after, and up and down again
- The nose is not accurate enough or wornOr the screws are not screwed in placeOr die inappropriate, too large
- Q: Where is the Huangyan extruder machine?
- You want to see what type of mold processing, but Masino comprehensive, injection mold, blow mold, mold and so on can be developed.
- Q: How to adjust the 65 screw gap in the extruder?
- This should be practical learning. The outlet plane of the barrel is about 3 mm in diameter.
- Q: Who knows the structure of the big extrusion machine head (has cooled), smash what structure, model of plastic crusher?
- How big is it? Not too big. I suggest using a 40 or 30 too big block. You have to use a special break knot. There is a kind of broken engineering material. I wonder if you can find it
- Q: What is the principle of the 45 extruder machine?
- The principle of the extruder is the theoretical process of heating, melting and mixing in the process of plastic conveying, including solid conveying principle, melt transportation principle, mixing principle, and solid bed crushing process, etc..
- Q: How many roots are produced in an hour for an PVC tube extruder?
- It depends on the type of your extruder and the specification of the tube you produced
Send your message to us
PE, PP, PVC And Wood Plate Extrusion Line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 30 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
