Curtain Wall System Long Single Arm Spider B220-1

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1. curtain wall spider system
2. made by casting
3. with genuine stainless steel
4. laser printing logo available

Table of Chemical Composition (%)

Product Picture:

Curtain Wall System Long Single Arm Spider B220-1

Other types spider in B220 Series:

B220-21 B220-1

Curtain Wall System Long Single Arm Spider B220-1

B220-4 B220-11

Curtain Wall System Long Single Arm Spider B220-1

Project Picture：

Curtain Wall System Long Single Arm Spider B220-1

Q: What is the difference between the price of the pick up claw?: Material 201,304,316, from time to good, the most commonly used is 304. The larger the size, of course, the price is smaller than the size of the expensive

Q: A set of curtain wall point of the stainless steel access to the claws, including what?: A set of curtain wall accessories include: such as four claws included, a four paw claw pieces, a adapter base, four split joints, to form a set, in the market are generally complete sets of quotes, but the market The price is expensive outrageous

Q: Glass curtain wall glass installation process requirements which out: The last step is the most critical step is to glue. Before the application of "xylene" or industrial ethanol and clean towels to wipe the stainless steel and steel tiles to fight the site, in the need to glue part of the paste protective tape, pay attention to adhesive tape and glue to be straight. Split the bottom of the stainless steel and the gap with the steel slot with a foam tape to tighten, to ensure straight, and set the net height of 8mm-12mm of the adhesive thickness. When the glue is full, the operation sequence is generally: first hit the horizontal seam after playing vertical seam; vertical glue should be from top to bottom, glue filled, should check whether there are bubbles, empty, broken, Mixed, if it should be dealt with in a timely manner. Every other day when the plastic joints, plastic joints should be cleaned up a good plastic head, remove the glue before the glue, to ensure that the two glue the connection closely. Stainless steel glue should be quickly modified after the adhesive tape will be torn on stainless steel, stainless steel plastic curing, should clean the inside and outside the stainless steel, do a good job protection signs. If the use of laminated stainless steel, the outer film thickness should not be less than 10mm, the thickness of the film should not be less than 8mm.

Q: Splicing the claws of the claws: The appearance of the glass curtain wall with the connection of the pawl is transparent, and the interior space and the outdoor environment are fused due to the lack of wall and good lighting. Split claws support structure and diverse, to meet the needs of different building structures and decorative effects.

Q: How many errors can be made by welding the splicing jaws: To be reasonable at the beginning of the adapter and the steel frame between the contacts designed, I make a simple example: Now there are a lot of steel frame is welded with a round tube, that adapter The base in the production of the time also need to be cut into the arc, so that steel pipe can be better connected to the tube, while reducing the interface of the degree of restraint, and secondly, reasonable arrangement of welding order to reduce the welding stress, Welding at the same time can reduce the heat generated when welding cracks. Welding starting point and the mouth is easy to produce cracks, conditional welding joints should be at the plus arc plate and arc plate. If you can not use the arc plate, the best use of attenuation current arc, and fill the crater. At the same time in the welding process in order to reduce the weld cracks, as far as possible the use of small lines of energy and cross-section of the welding point. If the process of welding found in the leak, if not serious, then gently knock with a hammer may be just fine. To avoid this is best to the workers carefully, in the welding when the cautious point of these problems can be avoided.

Q: What are the accessories of the point-supported glass curtain wall?: Point-type glass curtain wall accessories are stainless steel curtain wall adapter, split joints, split claws, glass clip, handrail pieces, rain canopy accessories, support rods, rods, cable, stainless steel mini cable and so on.

Q: Members of the master is good, I want to pull the claw side of the stainless steel support the side of the glass, one side installed in the antiseptic wood, please practice in the anti-wood that side how to install, how fixed on the wood preservative.: If the antiseptic wood beam is relatively large, then can be directly with expansion bolts fixed on the wood preservative. Taking into account the glass is relatively heavy and the common problem of anti-corrosion wood cracking, if you want to be more solid, you can use a steel plate to be set in the anti-corrosion wood beams (expansion bolts fixed), and then then welding welding on the steel sleeve.

Q: Will the glass curtain wall, 1600 * 2500 glass, 8 +8 glued rubber, with more of the appropriate claw claw, more than 60 meters of the building, so much glass stress enough?: If it is above the canopy, the general series, such as 220,250 series or even 300 paw pieces are enough, light If it is a facade curtain wall, then it is recommended that you choose the type of heavy-duty claw pieces, remember that the weight of the claw determines the load-bearing, while the corresponding joints to improve the proposed tough or imitation type weight, such as 250 Series of four claws 2.2-2.4kg pure jaw pieces

Q: What is the use of borehole during the production of tempered glass?: Drilling, opening is to meet the actual needs of the installation of glass, such as the installation of glass curtain wall need to open the claw hole, the installation of the glass door need to open the door clip, the handle hole, etc .; there are some special locations in order to open the obstacles Objects, such as beams, corners, etc., but also to maintain the overall appearance of the case, need to be punched on the glass, open missing.

Q: I do not understand the hope that my friends guide the guidance teach me, the general is divided into 150 160 type 200 type 220 type 250 type (4 claw) a set of refers to the splicing claws +4 turn joints +1 turn Parts There is the corresponding model with the corresponding splicing? Or with the model has nothing to do with the folder of the glass? Such as 150 can be used to replace the type of 200 can not use? Who explained the next: The same series of models of the splicing jaws can only be equipped with the same series of models of the joints, and glass has nothing to do, and the glass aperture is determined by the joints. The series of splicing claws is twice the distance between the center of the hole of the spliced joint and the center of the hole of the adapter. The distance between the center of the hole of the 250-piece claw fitting and the hole center of the adapter is 125mm, twice the 250mm, 250 series.

Send your message to us

*Email

*TEL

*Quantity

*Unit