Butterfly Valve Plastic Handle Made in China on Hot Sale
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Manual Wafer Butterfly Valve Description:
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Butterfly Valve
a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.
b)Soft seat. Replaceable. Increase of service life.
c)Double half shaft without pin.
d) Square and short neck. Easy to stick scutcheon and cost saving.
3. Manual Wafer Butterfly Valve Images:
4.Manual Wafer Butterfly Valve Specification:
5.FAQ
1. What is manual wafer butterfly valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.
2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
3. What is the working principle of manual wafer butterfly valve?
A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q: How to find all kinds of mysterious valves of human body?
- Many cell signal channels have been found, and if you can find each signal, the channel will be almost the same. That's the mysterious valve you want, but it's hard.
- Q: So how does the valve turn on?
- The handle of the valve is opened along the pipe and perpendicular to the pipe
- Q: What is the valve before and after the pump?
- General pump should be installed before and after the pressure regulating valve, pump installed before the pressure drop valve, pump installed after the pressure regulator valve!
- Q: What does the "Z45T-16" valve mean?
- Z - gate valve4 - flange connection5 - Dark pole, stem non lifting (gate valve structure)T - copper alloy, valve sealing face code16 - pressure code, 1.6MPaMaterial code for grey cast iron valves of nominal pressure less than or equal to PN16 shall be omitted in model preparation.May refer to JB/T 308 valve model compilation method
- Q: What are the production equipment in valve shop?
- Machining equipment: CNC, universal car, milling machine, drilling machine (rocker arm drill), wire cutting, grinding machineTest equipment: valve test press according to the production of valve pressure, specifications, types of procurement.
- Q: How do I open the gas valve?
- Third: in the following there is a black disk like thing, commonly known as the gas sound core. This one is the same as the second one, half or all. 1, according to the routine, now the handle position shows that the valve is open. 2, if the handle rotated 90 degrees, the gas pipeline gas has no change, should be the stem slipped, can not drive the valve ball rotation. Try rotating several times. If it still doesn't work, ask a professional to check it out.
- Q: What are the key valve enterprises in China? Mainly in those areas?
- This does not say, as if no one statistics! But you can check them on some big valve platforms, and there should be some statistics...
- Q: What kind of valves are best used for sand drain valves?
- Suzhou ATW Valve Co. Ltd production of sealing ball valve, Suzhou ATW Valve Co., according to the condition of solid particles, long-term research and in practice, and achieved good results in the condition of solid particles. You can try!
- Q: How can the material be checked by valve approach? What experiments do you need?
- May refer to the valve pressure test principle and the pressure test matters needing attention.(1) in general, the valve shall not be subject to strength test, but the body and bonnet shall be subjected to strength tests after the repair of the valve body and bonnet or corrosion damage. For the relief valve, the constant pressure and seat return pressure and other tests shall be in accordance with the specifications and the relevant regulations.(2) the installation of the valve should be done for strength and tightness test. Low pressure valve sampling 20%, if not qualified should be 100% of the inspection; medium and high pressure valve should be 100% of the inspection.(3) the installation position of the valve shall be in the direction of easy inspection during the test.(4) welding connection valve, not with blind plate pressure test can be used when the cone seal or O ring seal pressure test.(5) when hydraulic test, the valve air will be excluded as much as possible.(6) the pressure should be increased gradually during the test, and the pressure will not be sudden and sudden.(7) strength test and sealed test duration is generally 2~3min, important and special valves should last 5min. Small caliber valve test time can be a little shorter, large caliber valve test time can be longer. During the test, the test time can be extended if in doubt. Strength test, does not allow the body and bonnet sweating or leakage. Sealing test, the general rotor valve only once, the safety valve, high pressure valve and other raw valve to be carried out two times. When testing for the low pressure, large diameter valve is not important and there are provisions to allow leakage of the valve, allowing a small amount of leakage; the common valve, power station valve, marine valves and other valve requirements vary on leakage requirements according to relevant regulations.
- Q: Name: valve actuatorFunction: control valve switch by controlling air flow sizeIntended classification commodity code: 8412310090 (other linear acting pneumatic power unit, pressure cylinder)Shanghai Pudong Airport customs change classification: 84123900 (other pneumatic power unit)Commodity code information given by China Customs official network: 8412310090 (actuator, valve parts, valve actuation, pneumatic)Our goods encoding 8412310090 is classified to the Shanghai Pudong Airport customs dismissed, there are no friends of this commodity encoding on the official website of the detailed specifications defined, I Secretary in accordance with the valve function into 8412310090 encoding. Thank you
- The boring actuator, that is, the pneumatic valve actuator, is described in the customs notesPneumatic valve actuator (three) separately presented. This device is equipped with a piston metal enclosure, linear motion of compressed gas generated by a needle perpendicular to the piston rod into the rotary motion, in order to control plug valve or other device with a rotary deviceSo the Shanghai customs will bring you the list backIn fact, the most important point of distinction or the actuator is pneumatic energy conversion in what form movement of the mechanical energy output, if it is a straight reciprocating, 84123100 is correct, if not belonging to the rotary linear motion, or radians, 841239 correct
Send your message to us
Butterfly Valve Plastic Handle Made in China on Hot Sale
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches