Shower Organiser Pole Super White

Hot Products

FAQ

I am looking for some shiny gold 1 in tiles i need about 50-60 can anybody help me out. I would prefer ceramic cause they are gonna be used in a floor but ill take suggestions too.
check out a tile outlet store, id give a few names but i dont know if i'm allowed ,, also id think about going with porcelain tiles,,just for the fact that if 1 happens to chip,, the color is set the same the hole way through the tile, instead of just on the top, then u dont have to replace it
standard shiny, white 4x4 tiles. I want to redo the bathroom stalls, but heard from some people that it could take forever, and that i might end up messing up the the drywall? to me it sounds simple... just get a spatula or something of the sort and scrape off the tiles... is that how it goes or is it more difficult than that? has anyone out there done this? what tools would i need? what type of tile cutter do you suggest? i‘d like to replace the tiles with something bigger... maybe 10x10 tiles?
Being that your house is pretty new most likely the tiles are on drywall and set using latex glue. However if they were set using thinset cement on drywall it will be a little harder or if the builder used the older method and set the tiles in cement on wire mesh, then it's a beast and everything must come down. Using a stiff putty knife start at the top and tap the putty knife behind the tiles and gently pry away from the wall. You will have some damage to the drywall, apply drywall compound, let dry sand down and paint with primer. NOTE: Be sure to wear eye protection and gloves, broken tile is very sharp. Also protect your tub by installing a piece of plywood on top of it to prevent falling tiles from damaging it. It's also not a bad ideal to just tear out the drywall and tile and install new backer board. Maybe a little more work money but In the long run it will make for a much better job. If you are going to use that large of tile you really should tear it out and use the cement backer board and thinset as your glue as these tiles are heavy. Rent a wet saw to cut the tiles.
How difficult is it to strip and reseal saltillo tile floors? Is this something that I can do myself or do I need to hire a professional?
Stripping Saltillo Tile
Our kitchen isn‘t that big and I hate the tile. My fiance says it‘s a huge big deal to remove the tile but not so hard to put new tile in.About how much does it run to remove tile, say from the average size kitchen.... it‘s about 7 foot by 18 feet.
It should only cost about as much a sledge hammer costs. And you don't even need that big of one. Other than that just go in and hit it with the sledge and it will come up.
I have a basement about 25X25 does anyone know how much it would cost to put vinyl tile down?
Rhoda forgot the glue and the tax though for the other she is spot on and have fun with it. good luck
I‘m remodeling my kitchen back splash and bathroom shower and i love the Moroccan tiles. Does anyone know any source for Moroccan tiles in San Francisco, California?
The okorder / Cheers, and Good luck Anna,
Tiles 1 open 2 What does it mean ah?
Is a piece of brick to a half of the cut! For example, your brick is 800 * 800 open on the two 800 * 400 of the two
A roofing tile falls from rest off the roof of a building. An observer from across the street notices that it takes 0.32 s for the tile to pass between two windowsills that are 3.49 m apart. How far is the sill of the upper window from the roof of the building?
Called Vx the speed the tile has reached in free falling mode at the upper window's sill span = 3.49 = (Vx+(Vx+g*t)/2*t 6.98 = 2Vx*0.32+9.8*0.32^2 5.976 = 0.64Vx Vx = 5.976/0.64 = 9.34 m/sec (tile speed at the sill of the upper window) falling time tf = Vx/g = 9.34/9.8 = 0.953 sec (from roof to the sill of the upper window) h = 1/2gt^2 = 4.9*0.953^2 = 4.45 m h = Vx^2/2g = 9.34^2/19.6 = 4.45 m