Rectangular Flexible Duct Connector - The Wind Pipe Flexible Joint A Quality
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500000 pc
- Supply Capability:
- 5000000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Product characteristics
This product takes advantages of high flexibility and high air impermeability and medium resistance of rubber as well as compliance and heat resistance of glass— Fabric and is prepared at both ends with metal spool and flange in connection with wind machine and air duct, which can compensate the thermal expansion by the operation of air duct and multidirections displacement. For better compliance of rubber and fabric and good sound absorption and vibration isolation, the noise and vibration passage can be reduced effectively in the operation of boiler, wind machine and air current. Because the main materials are rubber or fabric and fiber heat preservation materials of light weight without thrust in reverse and in no need of pipe supporting seat, a lot of materials are used so it has good heat resistance and corrosion resistance. In addition, rubber has better air impermeability absolutely without leakage and with lower price than metal compensator and import products.
Installation Direction of Air Duct Rubber (Fabric) Compensator
Thanks for your application for our products, please read it before the installation:
In order to make air duct compensator achieve available effect in pipe and all mechanical performance play their right role and extend its use life, please make installation according to the requirements as follows:
1. Air duct compensator should be installed in pipe in natural conditions and the product distortion by contrived factors should be made in installation, so the products will avoid from early damage and weaker application effect.
2. When air duct compensator is installed to connect with flange, screw of bolt should stretch to the outside of flange to prevent the rubber (fabric) ball from being scraped by whorl tip. The bolt on the face of each flange should be screwed down equably by thread and it is required that all the degree of tightness should be as consistent as possible. In bad conditions, spring gasket can be added except flat gasket to avoid nuts from loosing.
| Factory | Firepower power plant | Air escape of boiler and gas turbine |
| Landification industry | Air escape of boiler and industrial furnace | |
| Fume extractor and desulfurizer | Warm and dry ventilating duct | |
| Metallurgy system | Fume and dust extraction of blast furnace | |
| Nucleus power plant | Air exchanging device | |
| Cement industry | Various kilns, dust collecting and fume and dusting extracting system | |
| Equipment | Dust collector | Entrance and exit of wind machines of all the equipment |
| Dust collector | ||
| Air heater | ||
| Washer | ||
| Induced draft fan | ||
| fan |
- Q: Drain flexible pipe to keep the base design above the elevation of the number of meters
- , there are cloth-based materials, such as Teflon cloth, etc
- Q: We now have to declare the Department of the Ministry of the United States and the United States, the company said that the access point to our own set, so I would like to ask, what is the requirements of this access point? There is no relevant specification to add: is the construction, the outdoor pipe network in the gas access point position more
- Construction workers classification and breakdown of ordinary types of work
- Q: Will the embedded stove why use stainless steel corrugated hose connection?
- 62-2 meets the requirements 3 The deformation rate of the flexible pipe shall not exceed the design requirements or the provisions of regulation 45 the longitudinal wall shall not appear in the pipe wall, and the annular and other deformation shall be in accordance with regulation 462-3 The requirements of the 4 backfill compaction should meet the design requirements, design requirements, should meet the requirements of Table 463- Table 463-2 Flexible pipe groove backfill site and compaction see Figure 463 Article 462-4 meet the requirements of the general items 1 backfill should reach the design elevation, the surface should be flattened Section 462-5 meet the requirements 2 backfill pipe and ancillary structures without damage, settlement, displacement Section 462-6 Conformity to allowable deviation Average pass rate (%)
- Q: Can the kitchen sewage pipe pass through the walls of the stove wall?
- scaffolding pole base with the height must be high longitudinal bar to the lower extension of the two spans and pole fixed height difference should be 1m by slope slope of the vertical axis of the slope should be 500mm single, double Row scaffolding bottom step should be 2m single row, double row and full of scaffolding stand in addition to the top of the top step outside the other layers of each step must be connected with the fastener scaffolding pole connection, lap should be consistent with the column Provisions: the use of connecting rods should be staggered with two adjacent rods should be arranged to set the synchronization within the synchronization within the separation of the two-phase separation of the distance from the distance to 500 mm; each connected to the main node the use of lap joint lap joint should be at 1m and should be used less than 2 rotating fasteners fixed end fastener cover edge to the rod end distance should be 100mm scaffolding Pole top rail bar should be high wall end 1m should eaves mouth 15m
- Q: On the classification of car repair, the best details Thank you Such as sheet metal workers, car circuits, etc. Thank you
- There are also special materials such as bamboo, so rare, no longer introduced
- Q: Why should the flexible hose be set in the mechanical ventilation system?
- Bowl buckle price is high! There are many buckle-style markets, so rent up cheap!
- Q: Is the clamp type flexible connector connected to the pipe to the rubber pad?
- See the situation, the general 3 percent or so, to see how the management of LZ, hand thank you
- Q: Is the flexible sleeve of the broken wall used as a second retest?
- The national standard is 18kg. Color steel sandwich panel is a common product in the current building materials, do not chu chu dumpling seal festival over the extinguished Long can only be a good flame retardant and environmentally friendly and efficient. Caigang sandwich board has two layers of metal panels and the middle of the polymer core insulation from the suppression. With the installation is simple, light and efficient light and efficient features. And the filling system used to close the molecular structure of the closed, you can put an end to the condensation of water vapor.
- Q: Maintenance Skills of Leakage of Fire Pipe Clamp Joint
- When connecting, first thread the bottom of the connector, and then screw the tapping screw into the threaded bottom hole of the connected part. As the tapping screw thread surface has a high hardness (≥ 45HRC), can be connected to the threaded bottom hole in the internal thread, thus forming a connection.
- Q: What materials are made of flexible pipes? Why should the mechanical ventilation set the flexible tube? Where should I be located?
- It is recommended to use the home of the heart of the card to worry about toughness to fill the joints, and then paste the seam (master understand) if directly in the sandwich panel (plate) on the batch of putty powder or spray painted really easy to drop off the phenomenon of stone, the first primer, it is recommended to use the home of the German brand brackish scraping scraping again There are), to be dry and then approved scraping putty powder spray really stone paint
Send your message to us
Rectangular Flexible Duct Connector - The Wind Pipe Flexible Joint A Quality
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500000 pc
- Supply Capability:
- 5000000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
