STAINLESS STEEL SLITTING CUT TO LENTH MACHINE
- Ref Price:
-
- Loading Port:
- Shekou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 6 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Automatical Slitting line
Components for the Line
The line includes in Atomatic decoiler w/coil car, guiding and leveling device, slitting device, cutting device, run out table and auto stacker. PLC control.
l Technical Parameters
Raw material specifications: Raw material: Pre-painted or galvanized steel
Thickness: 0.3~1.0mm
Width: 300—1260mm
Max weight: 5 T
Finished product specifications: width tolerance: ±0.5mm
Decoiler specifications: Max coil weight: 5T
Inner diameter: 350mm
Max out diameter: 1000mm
Slitting and cut to length device specifications:
Slitting speed: 0-20mm/min
Driving motor: 22 Kw
Slitting shaft diameter: Ф120mm
Shearing blade: 9 pieces,
Sepc: D220×d120×T10mm
Max slitting pieces: 6 pieces
Shearing blade material: 12CrMoV
Pinching roller: 2 couples
- Q: Bq: have you read elfen liedBq2: favorite quote from a book
- Kyrie- Mr. Mister Bq: No. Bq2: And in its sky was such a sun as no opium eater could have imagined in his wildest dreams. Too hot to be white, it was a searing ghost at the frontiers of the ultraviolet. (Childhood's End-Arthur C. Clarke-Chapter 16-The Last Generation)
- Q: what products does Zhengzhou Dayu machinery Co.,LD Produce?
- Poop farts
- Q: I just wanna know how much sea duty will they get and how much shore duty will they get? Is there a possibilty that they can get more shore duty? And yes i know i know when you are in the navy you're going to be on the sea thank you i heard that so many times lol!!!! But any answers will be great!!Thank you all and god bless
- The biggest difference is that the Navy Reserve generally work 1 weekend a month and 2 weeks a year with the Navy. Active duty Navy is on duty 24/7. There are some reservists that serve with the active duty Navy full time, mostly these are officers. This is done due to the limited amount of active duty officers the USN can have at one time and Reservists do not count towards this limit. You will see them listed as USN(R)
- Q: I have a go cart with a 6.5 horsepower general machinery small engine. The engine starts right up first pull but as soon as I press the throttle, the engine dies. The only way to use it is if you start the engine with the throttle being pushed, but if you let it idle for about 10 seconds after that it dies. Whats going on here??? Any help would be greatly appreciated.
- clean carb...idles ok but given gas stalls....when u hit throttle u open letting in more air...not enough gas..
- Q: Please send me information about some company manufacturing this machinery. I have heard that some overseas companies are there.
- See: okorder
- Q: What machinery/tools are need to make custom guns?
- It depends upon what all you are wanting to do. Just building ARs from stock parts takes some screw drivers, punches, barrel wrench, castle nut wrench, upper and lower blocks and a vise. You would also need a trigger jig for an AR to be able to tune triggers or even make them safe. To take barrels from a blank, you would need a lathe and chamber cutter. To make receivers or other parts from steel, you would need a milling machine. You may also need engraving tools if you plan on engraving any of the guns. A hot bluing tank could come in handy if you want to do any metal work. You should probably have a setup to do phosphate coating too. If you plan on doing any stock work, you would need a good selection of wood working tools. You would also need various jigs, dies and wrenches specifically for each model of firearm that you work on. There is not really any set list since it is so dependent upon what you want to do.
- Q: what rate of depreciation on new machineries purchase?
- The maximum section 179 deduction you can elect for property you placed in service in 2006 is increased to $108,000 for quali?fied section 179 property. This limit is reduced by the amount by which the cost of section 179 property placed in service during the tax year exceeds $430,000. Assuming you bought this equipment and it was placed into service in 2006, you dont have to capitalize it and depreciate it. You can elect to expense the equipment up to $108,000. This limitation gets reduced dollar for dollar for the amount of equipment placed into service in 2006 that exceeds $430,000.
- Q: please explain at 1 or 2...or 3. no current experiment please like knockout mice.
- 1. Griffith: injected mice with R cells mixed with dead S cells to prove bacteria can transform 2. Hershey Chase: used radioactive sulfur and phosphorous to mark proteins and DNA. injected bacteriophages in e li cell and found phosphorous entered cell, proving DNA is genetic material.
- Q: Have you ever driven heavy machinery like a fork lift?
- I never have personally, but I work with people who drive them everyday. I work in manufacturing. There's a little tug machine I drive sometimes but its simple and more like driving a car than a forklift.
- Q: what is machinery?and its uses.?
- Machinery is a series of components working together to accomplish a particular task. They can be crude, simple machines such as a block and tackle or very complex like a CNC Machine or a monster earth moving crane. Most machinery is used in production or manufacturing.However machinery is als o used to move a ship through the water, dig a tunnel or mine shaft, drill for oil, make a baseball bat, make candy etc. The uses are endless.
Send your message to us
STAINLESS STEEL SLITTING CUT TO LENTH MACHINE
- Ref Price:
-
- Loading Port:
- Shekou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 6 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
