Semi-electric Stacker SSPM
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1 unit/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Be applicable to the conveyance of factory, market , warehouse, wharf etc., the heap puts a goods demand of inner part to account heavy homework situation. It insures the operation in the meantime of safety.
- Q:Introduction of vertical elevator milling machine
- XD5032 X: milling word pinyin initials, on behalf of the milling machine D: should be on behalf of the manufacturer, 50: dalian is 32: vertical lifting platform structure is the most giant slalom spindle diameter of 320 mm
- Q:What standard elevator platform needs to go to the special equipment inspection to report
- Hoisting machinery, it is to point to used for vertical lifting or vertical and horizontal moving heavy mechanical and electrical equipment, its range is rated lifting weight greater than or equal to 0.5 t elevator; The weight is greater than or equal to 1t, and the lifting height is greater than or equal to 2m crane and weight bearing form fixed electric gourd
- Q:Put a large beaker of water on a horizontal platform and put a light glass upside down in the water
- The inside of the large beaker is raised, the pressure on the surface of the large beaker is larger, and C is right. The pressure of the bracket on the glass is downward, the pressure of the gas is rising, the glass gravity is constant, the pressure of the bracket is greater for the glass, and the D is wrong
- Q:How does the table in the middle of the tatami mat go up and down
- Need to buy the metal platform of suitable height, use screw to install small table board. Steps are as follows: Installation: desktop lock desktop board with screws on the top of the lifting platform (such as manual lifting platform should be first in the middle of the desktop is boring, the size of the hole to match the rocker tank size).
- Q:How does the elevator repair
- All parts should be filled with lubricating oil to extend the life of the bearing. The oil and oil level of hydraulic oil. The platform rises all the way up, and in this position, the hydraulic pressure should be 40 to 50 mm above the bottom of the box. Hydraulic oil is a variation of dark, sticky or grit, such as a discovery should be replaced in time (32 # hydraulic oil) Annual maintenance A. check all the hydraulic pipes and connectors. The pipe shall not be broken, the joints shall not be loose, and all the joints must be tightened. Remove and disassemble the descending valve, blow the plunger through compressed air, then load and resettle. C. the elevator hydraulic oil is put in the rejected, tighten the joint remove oil filter, after cleaning, use compressed air is clean, and then back into the tank, and the connecting line. (put on new oil and don't keep using the old oil. Otherwise, the moving parts in the system will accelerate the wear and tear.)
- Q:The home is decorated, make a tatami mat the platform should pay attention to what aspect?
- The key to the tatami mat is the choice of the middle lift. Attention should be paid to several aspects: the control mode of the tatami platform, the safety clamping system, and the manufacturer and brand.
- Q:Is there a replacement for similar elevating functions?
- This is not a press machine, a wacky experiment, a big nail in the press, and how much pressure to puncture a tyre.
- Q:Is the music console working? Want to start a, afraid to buy expensive again.
- The music and song platform is a one-stop alternate office product, which means you can stand for a while.
- Q:What hydraulic cylinder is used
- As long as the hydraulic cylinder reaches the required height.I hope my answer will help you.
- Q:How do you remove the horizontal universal elevator milling cutter
- When the milling cutter is removed from the vertical milling machine, the lever nut must be released and then the end of the rod is gently tapped. ; You should not release too much, as long as you have some loose space. When you release too much, the thread connecting the rod and the milling cutter is too short, and when you tap, you slip and even drop the knife.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Semi-electric Stacker SSPM
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1 unit/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
