Omni Direction Self-Propelled Electric Scissor Lifts
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
ntroduce:
The product is mainly applied in the fixing, constructing, detecting and maintenance of steel structure workshop and sorts of aerial equipment. With character of omnidirection and lateral-step, it can be operated in condition which space is limited and working height is tall. CE certified.
1)Structure: scissors, enable extended-platform, the setting of anti-press.
2)Sole control system, character of omnidirection, side drive.
3)Four-wheel drive, the direction of Mecanum wheel could be controlled separately by the control system.
4)Maximum speed: 4-5km/h.
5)Gradeability: 15%.
6)Pot-hole protection and tilt alarm.
7)Emergency down-valve device.
| Model | JCPT1013(OD) | JCPT1213(OD) | |
| Rated capacity | kg | 450 | 400 |
| Extend platform rated capacity | kg | 112 | |
| Wind speed 45km/h | kg | 100 | |
| Max working height | mm | 10000 | 12000 |
| Max platform height | mm | 8000 | 10000 |
| Overall length | mm | 2510 | |
| Overall width | mm | 1300 | |
| Overall height | mm | 2450 | |
| Platform size | mm | 2500X1120 | |
| Platform extend length | mm | 1270X1120 | |
| Ground clearance | mm | 120 | |
| Wheelbase | mm | 2030 | |
| Turning radius | mm | 0 | |
| Drive motor | 4x48VDC/2kw | ||
| Lift motor | 48VDC/2kw | ||
| Drive speed-stowed | km/h | 5 | |
| Drive speed-raised | km/h | 1.1 | |
| Raising/Falling speed | sec | 70/60 | 89/88 |
| Battery | 8x6V/250Ah | ||
| Charger | 48V/30A | ||
| Gradeability-stowed | ％ | 20 | |
| Max angle | 。 | 3 | |
| Tyre | mm | 430 | |
| NW | kg | 2500 | 2550 |
Standard Configuration
-Can bus line intelligent controller
-Proportional controller
-Charge lamp
-Automatic pot hole protection system
-4x2 drive
-Transport standard forklift hole
-Tilt protection
-Tilt alarm
-Horn
-Working chronometer
-Electric circuit fault code display
-Low voltage alarm
-Extended platform
-Charge protection
-Omni drive travel system
-Overload limit
-Controller overtemperature protection
-Driving motor overtemperature protection
-High capacity traction battery
Optional Configuration
-AC power source connected to platform
-Working lamp
-Rotary strobe light
- Q: What about the heat treatment of the lifting platform?
- Heat treatment service condition and performance requirement of ball screw Screw transmission is the key to all kinds of machine tools, it is converting rotary motion to linear motion or linear motion into rotary motion transmission, positioning features. There are two main types of machine tools, such as trapezoidal screw and ball screw. The ball screw transmission efficiency is high, action quick, feed is steady, low speed crawl, positioning accuracy and repeat precision is high, long service life, widely used in nc machine tools and machining center.
- Q: How does the table in the middle of the tatami mat go up and down
- Opposite position: put the platform and the table board into the central pit of the tatami mat. Drop the lower part of the platform to the bottom, make the table and the tatami mat surface level, and adjust the horizontal position to make the gap between the table and the table evenly.
- Q: What is the elevating platform for automatic mahjong machine?
- The bearings and screws on the lifting mechanism fell off. Solution: open the lid of the machine box under the mahjong machine, and you can see a circular black iron piece fixed on the motor, with a screw hole in it. Find screws and bearings in the box, spring pads, some machines and nuts. Just fix it up.
- Q: What kinds of tables are there? Which is better for the office?
- Hand. This is a waste of time and noise. 2: electric. Electric lift, mute. The downside is that you need to replace the whole table. 3: lifting platform. This is a table that is on the table, which is placed directly on the table and does not need to be installed.
- Q: You need to make a small lift platform, on top of the robot, non-industry. What you want is to add a light pole with a nut and a bolt, and you can use an electric motor to turn the bolts and the nuts.
- If use reduction motor may speed not soon (and consider the design of lifting platform under actual gravity reduction ratio), the situation of the specific need according to the design requirements, weigh the pros and cons.
- Q: What is the price of the hydraulic platform
- Mobile I have dozens of it are common, such as 0.3 T - 0.5 T - 3 M price about 15000 yuan 3 M is 18000 yuan 1 T - 4.5 M is 21000 yuan price basic like this, look at your own ability to discount.
- Q: Introduction of vertical elevator milling machine
- XD5032 X: milling word pinyin initials, on behalf of the milling machine D: should be on behalf of the manufacturer, 50: dalian is 32: vertical lifting platform structure is the most giant slalom spindle diameter of 320 mm
- Q: Is the music console working? Want to start a, afraid to buy expensive again.
- It belongs to the table at the table, which means you can use it when you remove it and put it on the table.
- Q: The automatic mahjong machine has a lift station always one. What is the other three normal
- The synchronous motor is out of control, or the motor is broken by a series of windings
- Q: Simple manual lifting mechanism, a nut a bolt can
- Handle is fixed below the floor below need not fixed, it is not fixed under the base plate is fixed, the floor below the retaining common shim fix the quotas for marketing or for cap.
Send your message to us
Omni Direction Self-Propelled Electric Scissor Lifts
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
