picture frame extrusion equipment with competitive price
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
photo frame equipment
1) PS foam Plastic Frame Profile Production Line is the newly developed production equipment in plastics machinery industry.
(2) Heat transfer unit which is based on imports of inproved design prototypes made it is mainly used in hot-stamped on the frame profiles .
(3) The aircraft have exterior appearance ,reliability,precision stamping adsorption and strong and adjusting hand wheel can imprint a variety of different shapes of the profiles.
Machine: PS foam Plastic Frame Profile Production Line
Ps foam profile production mainly consists of the ps foam sections dedicated single-rod extruder and co-extruded side machines cooling tanks heat transfer units teaction machine cutting machine stacker component machine speed control system with ac inverter control temperature control instruments and other components imported with a good plasticization high output stable operaion and so on .
Main technacial parameter:
Configuration
Name | Quantity |
the special co-extruder | 1 set |
SJ65, SJ90,SJ100,SJ120 single screw extruder | 1 set |
cooling water tank | 1 set |
hot stamping machine systerm | 1 set |
Haul off machine | 1 set |
cutter | 1 set |
Tipping stacker | 1 set |
- Q: when I use armature voltage feedback (host start speed 50, normal can produce 10It is normal to start at 80 or 150 of the speed, but after a few minutes the motor does not turn. 590 alarm (missing pulse alarm). When I change the feedback mode to speed feedback, my host sometimes starts and sometimes fails to start. I hope you help me, how should I adjust?. Thank you。
- You can adjust the proportional gain, and if you don't move, the parameter has this problem, you should check to see if you really lost the pulse
- Q: Produce 10 square wires with the smallest extruder
- If the production of single core line, then 50 machines can also do, but low efficiency, unstable line,.70 or 90 machine idealIf it is a production sheath line, do at least 70 machines, preferably 70 or 90 insulation, and 90/120 as sheath
- Q: Plastic double screw extruder, pumping air will accumulate material, how is it going on?
- Adjust the assembly and check the exhaust block
- Q: Cable extruder how to match the mold, how to calculate the formula, ask the master pointing
- Look at what you have in the form of mold, extrusion, drawing, or half pipe
- Q: the machine vibration is great, the motor, reducer are checked, no problem, there is abnormal sound.
- Is the fitting of the moving parts normal?.Is there an impact on the extrusion chamber?.
- Q: Extrusion blow molding machine, storage or continuous type good?
- and material in the screw for a long time to use the storage type is also in order to meet the demand for raw materials productsIf you are doing small things, your hourly output will not consume the maximum hour.
- Q: PVC extrusion machine extrusion stone floor no pressure, what reason?
- PvC stone floor extruder pressure is adjusted by the screw and die head
- Q: Which type of inverter is suitable for extruding machine? Please give expert advice, and G series is discontinued
- They can see it moving.God doesn't need itSometimes you hear, fifth hand material,Cool sounds in the swirling smokeCoagulation together, I have left their land,Yesterday was a similar experience, ha ha
- Q: Extrusion machine operating procedures, specific points, thank you!
- 1, operators must be familiar with the procedures, the safety test qualified, wear good protective equipment, shall operate the equipment.2 when the power is on, check whether the thermal control of the electric appliance is sensitive and reliable, whether the thermocouple indicates the temperature is correct or not, and if there is a problem, please repair the personnel to exclude them.3 when driving, should check the main reducer, traction non polar transmission, the line is stepless gear box lubrication is normal, fan ventilation is good.4 before driving, pay attention to the heating temperature of each section, whether the actual temperature required by the process, the heat preservation time should be enough, and the initial heating time can not be less than 3 hours heat preservation.5, not in the plastic bad, scorched, aging, extrusion production, in case of accidents, and found the above problems, immediately try to rule out.
- Q: Does anyone know the operating procedures for the cable 65+120 extruder?
- What are the operating specifications for the extruder?One is the equipment instructionTwo is the boot operation specificationsThree is safety instructions and so onThe equipment manufacturer will provide the above
Send your message to us
picture frame extrusion equipment with competitive price
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
