PE-PVC wider geomembrane sheet extrusion line
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
this machine products application :
Used for different kinds of plastic material, such as PVC, TPO, PE etc.Being able to produce below sheets:
For waterproofing usage in industrial & civil buildings including the green roof, flat roof and the sloping roof. Underground waterproof：reservoir、dam pool. waterproof usage in tunnel, grain depot, artificial engineering, landfill, Artifi- cial lake.
- Q: What is the waste gas produced by the extruder, granulator and mixer?
- Do you want water spray, dry filter, carbon adsorption, fan, and discharge? Will that be better, thank you?Chasing the answerIf the exhaust gas contains acid and alkali waste gas (slightly acid base acceptable), there is no need to water spray, the main role of water spray is used to neutralize the acid and alkali containing exhaust gas. The exhaust gas is dry organic waste gas, only dry filter, activated carbon adsorption odor can be discharged.
- Q: What impact does the extruder vacuum pump open or close on the extrusion product?
- If the vacuum pump is opened, the air in the extruded product will be removed and the product material will be more closely packed. If the vacuum pump does not open, it may cause bubbles in the extruded product.
- Q: Wire and cable extrusion machine temperature exceeds the process documentation, what are the reasons?
- As far as actual production is concerned, it is necessary to go beyond the regulations to produce normally
- Q: Produce 10 square wires with the smallest extruder
- If the production of single core line, then 50 machines can also do, but low efficiency, unstable line,.70 or 90 machine idealIf it is a production sheath line, do at least 70 machines, preferably 70 or 90 insulation, and 90/120 as sheath
- Q: What is the adjustment method of China's extrusion machine die?
- (2) run mode: plastic glue on the plasticizing after adjustment for mold screw, die according to how much glue circle, ran glue, side adjustment, adjustment should be loose thin screws, tighten the screws run glue thick; at the same time sampling check plastic thickness is eccentric, until evenly so far, then tighten the screw die respectively.
- Q: Before and after the original good tune, up and down again before and after the tune, before and after, and up and down again
- The nose is not accurate enough or wornOr the screws are not screwed in placeOr die inappropriate, too large
- Q: Why? What is the raw material of plastics? What is the process flow of the process?.
- 1. injection molding2., the structure is relatively complex, high appearance requirements. Extrusion does not meet requirements3. most are: ABS, ABS+PC, PP and so on4., according to color requirements granulation - drying particles - filling the mold ---- debugging injection molding machine ---- injection molding production - after the selection of finished packaging (if silk screen requirements, but also the need for silk screen)
- Q: Extrusion machine operating procedures, specific points, thank you!
- 1, operators must be familiar with the procedures, the safety test qualified, wear good protective equipment, shall operate the equipment.2 when the power is on, check whether the thermal control of the electric appliance is sensitive and reliable, whether the thermocouple indicates the temperature is correct or not, and if there is a problem, please repair the personnel to exclude them.3 when driving, should check the main reducer, traction non polar transmission, the line is stepless gear box lubrication is normal, fan ventilation is good.4 before driving, pay attention to the heating temperature of each section, whether the actual temperature required by the process, the heat preservation time should be enough, and the initial heating time can not be less than 3 hours heat preservation.5, not in the plastic bad, scorched, aging, extrusion production, in case of accidents, and found the above problems, immediately try to rule out.
- Q: How many roots are produced in an hour for an PVC tube extruder?
- It depends on the type of your extruder and the specification of the tube you produced
- Q: Who knows the temperature regulation method of the extruder?Any information will do
- 1, extrusion methodAccording to plasticizing methods: dry extrusion and wet extrusionPress the way: continuous extrusion and intermittent extrusion2, characteristicsContinuous production, high efficiency, simple operation, wide range of applications [Edit] paragraph extrusion molding equipment 1, the hostExtrusion system: composed of screw and barrel, it is the key part of extruder. Its function is to melt plastics, quantitative, constant pressure, constant temperature extrusion of meltDrive system: drive the screw to increase the required torque and torqueHeating and cooling system: guarantee the temperature of plastic and extrusion system in molding process2 auxiliariesIt is composed of head, setting device, cooling device, traction device, coiling device and cutting3 、 control systemIt consists of electric apparatus, instrument and actuating mechanismPurpose: to control the main and auxiliary motor, in order to meet the demands of speed and power; control main engine temperature and pressure and flow, to ensure product quality; to achieve automatic control of the extrusion unit, ensure the coordinated operation of main and auxiliary equipment. [edit this paragraph] extruder extruder overview of plastic extruder is the host, it consists of extrusion system, transmission system and the heating and cooling system.
Send your message to us
PE-PVC wider geomembrane sheet extrusion line
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
