PE-RT Water Pipe for Floor Heating System
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 5000 m
- Supply Capability:
- 3000000 m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Descrition of Product:
platic pipe for hot water floor heating Pe-rt pipe : material:PE-RT
pipe for floor heating
Features:
1.Healthy
2.High temperature resistance
3.Corrosion resistance
4.Heat preservation
Advance:
1. Good thermal stability and long-term pressure resistance performance;
2.Excellent processing performance;
3.Good flexibility and easy for construction;
4.Good anti-wallop performance and high safety;
5.It can be connected by thermal fusion and easy for installation and maintenance;
6.With high performance-price ratio
FAQ:
① why from okorder？
Okorder is a qualified supplier of all kinds of building matierials in China. All products have been showed in Okorder website are under well controlled by okorder QC team.
All products had been produced under a clear quality standard and the quality is consistence among the shipments.
Okorder has already setted up more than 20 warehouses in different markets to show the products. You are convenient to know the products from your local place and it will help you to make decision easyly.
②How to guarantee the quality of the products？
We have established a perfect quality management system，as for raw material and semi parts all are under strict quality test and we have a IQC system to control the purchases.
QC on site is very strict and all steps of process are measured per drawings. Before delivery, we set a OQC system to make sure each piece meet the standard of order.from design to delivery,
③How long can we receive the product after purchase?
Lead time depending on order quanity, The normal order can be deliveried with 3 weeks.
- Q: I see the panel has a "cycle of digital time relay", the United States called microcomputer controller, as well as seismic pressure gauge, the rest is the switch indicator light, and there is no knowledge of what (estimated that there are two A solenoid valve a tube of water a gas), this thing on the market to sell more than 2000, I feel the cost of 200 to 300 yuan (guess, because I do not know where the burden of the child to pay the nuclear shop is too much money). Hope to tell the internal structure, which there are any components, I would like to do one, have a better picture, as well as cleaning, "time relay" set parameters (water and ventilation time), hope you greatly educated, brother Thank you The More
- come on, come on, come on
- Q: What are the heating components of the heating system design?
- What are the heating components of the heating system design?...
- Q: Whether the groove card can be used for heating pipes
- Not suitable for the groove in the gasket is rubber material heat resistance is not high long-term thermal environment will cause the gasket aging caused by leakage
- Q: Discusses the working principle of home split air conditioning and draws the schematic diagram
- I've learned that my book is there. I also have annotations to explain. ...
- Q: To install the mixed water center also installed with a pressure differential bypass valve
- The role of mixed water center is mainly to adjust the warm water supply problems, to achieve automatic control of water supply temperature. Reason: According to the provisions of the country to warm the installation, the water temperature should not be higher than 60 ℃: 1, to prevent the warm water in the warm pipe, water mixers and other heating system components in the scale. 2, to warm the pipe material for the plastic material, the higher the temperature of the working environment, the greater the pressure, will shorten the warm life. Municipal central heating more in accordance with the heating film heating temperature of 80 ℃ to the water, far more than the warm to apply the highest temperature. The mixed water center can mix the low temperature water of the heating system backwater into the water supply pipe, lower the heating water temperature, and then supply it to the floor. Refer to the following figure: Madison fireplace, dedicated to your service.
- Q: Does the gas ratio valve of the boiler be airtight
- The gas proportional valve is mainly based on the current command or load demand of the main control board of the boiler, instantaneous opening, shutting off the gas source or in the air supply state, according to the different needs of heat load, current affairs to reduce or increase the gas flow A combustion system components, generally consists of two safety off valve and Fuhai Dili destroy Gao Ji Dian top hug a proportion of regulating valve composition. If the gas ratio valve fails, then it may cause the boiler to work properly. General recommended direct replacement, maintenance is relatively cumbersome, not necessarily repaired.
- Q: We have two or three years useless to warm, the annual temperature is about 23 degrees. This year is still not hunger view spy grab the silicon oblique helmion want to, do not know the ground heating facilities have no harm, need to pay attention to what? Question added: water to warm, thank you! More
- Electricity to warm no problem, the water should pay attention to scaling and frost and other issues.
- Q: What is the difference between a warm water and a water separator?
- The role of the water separator is the heat source of hot water separately into each side of the ground radiation heating pipe laying, to achieve sub-room heating and temperature adjustment purposes. The sump is a combination of low temperature water in each way after the heat dissipation is separated and fixed to the wall or the ground. The manifold and the sump are made up of supervisors, shunting valves and joints, exhaust valves, drain valves, and terminal plugs. The use of sub-catchers effectively avoid the loopholes in water management, centralized installation, management of water meters, and with single-tube multi-channel.
- Q: The pressure to look at the floating spring faint tempered tents touching up in the 1.5 or so, after the opening of the heat will be similar to the heat will see the temperature will rise but it is not put out hot water, and the ground is not hot feeling. But also to open what valve? What is the black valve below the machine? More
- Any boiler before starting the machine to pay the water to see if the water pressure gauge pointer is between 1 - 1.5bar. If the water pressure in the above range, open the gas pipe valve, power on, set the machine in the winter position, set the heating temperature, usually the upper limit of the floor heating temperature can be set to 55- -60 degrees Celsius, radiator heating up to 75-85 degrees Celsius (if the radiator is not anti-hot protection, it is best to set the temperature a little lower). After normal ignition do not have to ignore it. Bath: see the water pressure gauge pressure is normal, open the gas valve, power on, set the machine in the summer position (if it is winter, that is set in the winter position), the hot water temperature is set at 42-45 degrees Celsius Between, open the hot water head, until the water temperature is appropriate and stable after you can start bathing. Antifreeze: water pressure gauge pressure is normal, the machine power plug (do not boot), the gas path open (must ensure that the gas source) can be. The above operation applies to Faroe, Haas, Ariston, Bosch, Squirrel, Beretta and other brands of boiler
- Q: Public bath with water heating
- The cost is too high to operate.
Send your message to us
PE-RT Water Pipe for Floor Heating System
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 5000 m
- Supply Capability:
- 3000000 m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
