Mono Crystalline Solar Panels with High Quality of CNBM
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 20000000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Product Description:
Monocrystalline Silicon Solar Panel
Introduction of Monocrystalline Silicon Solar Panel CNBM Solar photovoltaic (PV) Panel is designed for large electrical power requirements. It is the optimal choice for both on-grid and off-grid power systems. CNBM Solar panel offers high performance of power per square foot of solar array. Monocrystalline silicon(c-Si): often made using the Czochralski process. Single-crystal wafer cells tend to be expensive, and because they are cut from cylindrical ingots, do not completely cover a square solar cell module without a substantial waste of refined silicon. Hence most c-Si panels have uncovered gaps at the four corners of the cells.
Characteristics of Monocrystalline Silicon Solar Panel
I Solar Cell : High efficiency crystalline solar cell. Even if under the weak light, the solar module can produce maximum power output.
II Tempered glass (toughened glass): Anti-reflecting coating and high transmission rate glass increase the power output and mechanical strength of solar module.
III EVA and TPT: Using high quality EVA and TPT to prevent destroying and water.
IV AI frame: Without screw, corner connection. 6 holes on the frame can be installed easily.
V Junction box: Multi function junction box with water proof.
VI Long lifetime: ≥25 years; Less power decrease.
VII Good performance of preventing from atrocious weather such as wind and hails.
VIII Resisting moisture and etching effectively, not effected by geology. Standard Test Conditions of Monocrystalline Silicon Solar Panel The opto-electrical specifications shown below are stabilized values being measured at Standard Test Conditions, Irradiance: 1000W/m2, Spectrum: AM1.5 at 25°C, The info below is subject to manufacturing tolerances. Where appropriate minutes of measurement are available and are used for the dimensioning of the installation.
IMAGES:
FAQ:
WHAT'S THE ADVANTAGES OF CNBM?
1.CNBM is a state-owned company under jurisdiction of central goverment , one of Fortune 500 .Just because of this ,we can get more support and resources from our government.So ,it is realiable .
2.CNBM's solar products are high-qualified with TUV,UL,VDE,CE,ISO certificates. Our products ranges top in China.
3.Just as I mentioned in attahment ,we signed 500MW project with Urkan under the witness of our chairman Xi Jinping ,CNBM has ability to meet your large quantity needs,Our annual capacity is 1GW.
4.We can offer you a competitive price .Because you are our potential and valued customer .
- Q: I am searching for producers or distributors of solar panels. Thanks!
- Grimcho..I'm going to give you a secret that no-one I know of has ever spoken of..Call Your local railroad maintenance yard and/or your local oil production company..I know your probably in another part of the world where this will not apply but here its like this.. BNSF changes out every 2-5 years their 00w 24v panels...they still have a good 5years of lifetime..Oil companies change them out on their well sites every 2 years 2x 60w 24v (actually they are 2 +2vdc grids series) now if your in Italy sorry this didn't work but if your in New Mexico ..they are in Santa FE...also they have way good batteries that are wet cell and run about 600$ each that they just dump many times on the guy for asking..try it....From the E....
- Q: My house uses 500 kw a month, air conditioning is the main consumer, is it possible to install solar panels in my roof to produce this amount, and aproximate cost, thanks .
- 500 Kw
- Q: i hav e a project for school we need to calculate cost to buy and install solar panels in our school
- Photovoltaic panels have almost zero recurring operating cost. Once installed, they are good for the next 20-25 years, typically. The exceptions are if the panels are not tilted, then you need to pay someone a few times a year to go up there with a mop to clean them. Otherwise, rain and morning dew make the dirt slide off automatically. The cost for your system will depend on the power needs of your school. It also depends on your location. As a government entity, a school is not eligible for the current 30% federal incentive, but may be for state incentives, depending on where you live. Anyway, once you size your system, which will be large, figure on $7 / watt cost for a large system. This would be less if you live in a state with good incentives. So for example, if you needed a 00 kW system, the price would be $700,000. $00,000 of that money is to replace the inverters that break after 5 years, so you would be paying $600,000 up front.
- Q: does it mean that it can get that much in a day? Or like, in an hour?
- Wattage okorder
- Q: I bought a pack of OEM mini solar panels that produce 4.2v and 22mA and I was just wondering how many LED's I could hook up to one mini solar panel? I currently have one green LED with a resistor on the one panel but was wondering how many I could possibly run off of one panel?
- Typically LED's run off low voltage and 20mA or so of power (it depends what kind of led you have). That being said if one of your solar panels only provides 22mA of power then your circuit would have to be a series circuit for you to connect more than one. In a series circuit the current supplied of 22mA will go through each LED whereas a parallel circuit the current would be divided for each subsequential led. So in your case i can see you getting away with 3 or so led's before the voltage drop across each led will cause the voltage to be insufficient enough to drive anymore. Keep in mind the LED's will turn on but the first one will be bright then next one not as bright and so on. If you opted out and bought a solar panel with 200mA and 4V you could wire the led's in parallel and get 0 led's to turn on with the same brightness or intensity. Hoped that helped!
- Q: I was just wondering what the minimum and maximm charging voltage and ampere is for li ion batteries. If i connect a solar panel, which only gets enough sunshine to generate voltage, will that still charge the battery, or would i have to series connect solar panels until they together reach 3,7volt?
- One lithium cell requires 4.2V to obtain its full charge, Never exceed 4.2V ! Output from solar panel if below 3.7V , nothing charge to lithium. Total charging time until the cell is full depending on the AH rate of cell and the charging current that solar panel can be provided. Suppose cell is rate 5AH, and the charging current from solar panel under full sun shine can maintain 0.5A ( use solar panel short circuit current rate from its specification as a reference ) , hence, 0 hours is enough. And be sure the solar panel can maintain 4.2V output at 0.5A . Remember, over charge lithium cell one time might reduce its life into half . Therefore, let the solar panel output passing through a precision regulator to maintain output is 4.2V is the best way, because, as cell reaches 4.2V , no more charging current is forced into cell ( automatic stop charging ). If you do not have the knowledge to make this simple variable voltage regulator with LM37K ( if you choose this way, buy solar panel output has at least 2V) , you may choose to do it manually by install a current meter and a variable resistor in series between the panel output to cell. By adjust the value of resistor, charging current can be controlled ( if you choose this way, buy solar panel output has as less as 6V ). Count the charging time with a clock and adjust the charging current from time to time to maintain 0.5A .
- Q: How can solar panels be used for heating water?
- Solar panels can be used for heating water by capturing sunlight and converting it into electricity. This electricity can then be used to power heating elements or heat pumps that warm up water for various purposes, such as domestic use or swimming pools.
- Q: Harbor Freight sells a 75 watt solar panel, a surge power inverter, and deep charge batteries. But no one there can tell me how to put it all together. I want the end output to be a simple power bar that I can plug my devices into. I live in an apartment so I can not wire it directly into the grid. Please only serious responses. Don't waste your time and mine.
- i wouldn't. - harbor freight isn't known for the best quality stuff. - 75 watts assumes roof mounting, at 90 degrees to the sun, on a bright day. you're going to get considerably less. and only when the sun is highest in the sky. maybe you should look at, your computer, for example. if you're using it for 4 hours, and it has a 500 watt power supply, and you add 200-500 watts for the monitor, and some for the printer, modem, etc, you'd use 5kw that day. your 75 watt panel, generating maybe 50 watts at most, for maybe 4 hours when the sun was highest, and shining directly on the panel, would generate 200 watt hours. it would take 25 days to generate the electricity you'd use in single day. in the winter, you'd be pretty much out of luck. there just isn't enough bright sun. clearly, it's up to you, but there's a harbor freight near me, and i'll not be rushing out to get such a system. further, most appliances are quite voltage sensitive. you really do need to have the voltage in the 0-20 range. too much out, either higher or lower, will shorten the life of appliances at best.
- Q: i also need to know how does a solar panel work
- solar panels work in an interesting way. light is absorbed by each solar cell, and light 'photons' bump into electrons to produce 'voltage'/power. the process is naturally called the 'photo-voltaic effect'. the loose electrons are captured by an electrical conductor in the solar cell (usually made of silicon) and a circuit is completed ... solar panels may generate more power than is actually needed. this extra power is simply stored in lead-acid batteries (they store upto 000 watts). read more about it here...
- Q: What are the different types of solar panels?
- There are three main types of solar panels: monocrystalline, polycrystalline, and thin-film. Monocrystalline panels are made from a single crystal structure, offering high efficiency but also higher costs. Polycrystalline panels are made from multiple crystal structures, slightly less efficient but more cost-effective. Thin-film panels use a layer of semiconductor material, providing the lowest efficiency but the ability to be flexible and lightweight.
Send your message to us
Mono Crystalline Solar Panels with High Quality of CNBM
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 20000000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
