Low Resistance EDM Graphite Electrodes for Ferroalloy Plants
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 20mt m.t.
- Supply Capability:
- 20000MT/year m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
About Carbon Electrode Paste
Carbon Electrode Paste is a self-baking electrode used in submerged arc furnaces for delivering power to the charge mix. Electrode Paste is added to the top of the electrode column in either cylindrical or briquette form. As the paste moves down the electrode column the temperature increase causes the paste to melt and subsequently bake forming a block of electrically conductive carbon. Electrode Paste is essentially a mix of Electrically Calcined Anthracite (ECA) or Calcined Petroleum Coke (CPC) with Coal Tar Pitch.
Package: In MT jumbo Bags or on pallets as discussed with the buyers.
Specification for carbon electrode paste:
PARAMETER UNIT GUARANTEE VALUE | ||||||
Ash.( % ) | 4.0 max | 5.0 max | 6.0 max | 7.0 max | 9.0 max | 11.0 max |
V.M (%) | 12.0-15.5 | 12.0-15.5 | 12.0-15.5 | 9.5-13.5 | 11.5-15.5 | 11.5-15.5 |
Compress Strength. (Mpa) | 18.0 min | 17 min | 15.7 min | 19.6 min | 19.6 min | 19.6 min |
Specific Resistance (μΩm) | 65 max | 68 max | 75 max | 80 max | 90 max | 90 max |
Bulk Density (G/CM3) | 1.38 min | 1.38 min | 1.38 min | 1.38 min | 1.38 min | 1.38 min |
Pictures:
- Q: The reason why graphite is used as electrode
- The graphite has good conductivity and thermal conductivityThe conductivity of graphite is one hundred times higher than that of ordinary non-metallic minerals. Heat conductivity exceeds steel, iron, lead and other metal materials. The coefficient of thermal conductivity decreases with increasing temperature, and even at extremely high temperatures, the graphite becomes hot.
- Q: Why should graphite paper be placed between the heater and the graphite electrode?
- Heater design, the common heater has three shapes, cylinder, cup, spiral, the vast majority of the current heater is cylindrical, as shown in figure. The spiral heater has complicated processing technology and has been eliminated. Cup shaped heater for hemispherical crucible, the bottom melt temperature is more uniform, because the processing technology is difficult, already no use. Nowadays, most of them use cylinder heaters. The cylindrical heater is not only easy to process, but also is related to the large number of flat crucible used in the direct drawing single crystal furnace.
- Q: How much does a graphite electrode cost about a ton?
- According to purity and quality, the price is 1-6 tons / tonDo not calculate the processing cost
- Q: The graphite electrode made by the machining center adopts cooling method, which is water cooled, oil cooled and blow cold. Which is good?
- In addition, the infiltration of water on graphite is not good, can not get the effect of dust removal. Now there are special graphite machine, sealing system. Air-cooled can be used, after all, the best air-cooled.
- Q: What are the losses in graphite electrode?
- In what environment is the loss, friction, or in the case of high temperature, high temperature will be oxidized, and if in the case of friction, you can first use more wear-resistant graphite material. So please ask this question clearly, and then answer you, thank you.
- Q: Excuse me, why does the graphite electrode flake when electrolyzed salt water is used?
- For example, according to connection of the electrode, which can be divided into two types of unipolar and bipolar type electrolyzer (see photo). The electrode is connected with the DC power supply parallel polarity monopolar electrolyzer, electrodes on both sides of the same, at the same time as anode or cathode. At the same time as the positive and negative electrode bipolar type electrolyzer ends respectively with DC power supply connected, as anode or cathode. The current through the electrode through the electrolysis cell in series, each side of the intermediate electrode as the anode, the other side is the cathode, so it has a bipolar electrode. When the total area at the same time, the current bipolar type electrolyzer is small, high voltage DC power supply, the required investment ratio monopolar, bipolar type filter press used. The general structure, more compact. But easy to leakage and short circuit, slot structure and operation management is more complex than the monopolar type. The monopolar electrolyzer section is generally rectangular or square, cylindrical covers a large, empty The utilization rate is low and the adoption rate is less
- Q: What about graphite electrodes for steel mills?
- Hebei North graphite electrode factory produces various specifications of graphite electrode, with low resistance, high density, small ash, and so on, so that less tons of steel-making, quality is good
- Q: I remember the more lively metal, the electron?
- C metal is copper, because a dilute sulfuric acid into the H2 precipitation, then definitely not copper. And the inactive first precipitate
- Q: What does graphite electrode GSK mean?
- Graphite is made of high-strength graphite, it is a kind of graphite grade specification.
- Q: Graphitized anode, cathode and graphite electrode, respectively How can one differentiate and use differently?
- Compared with other materials of graphite anode plate has high temperature resistance, good electrical and thermal conductivity, easy machining, good chemical stability, acid and alkali resistance, low ash content; for electrolytic solution, preparation of chlorine, caustic soda, salt alkali electrolytic solution preparation; application such as graphite anode plate can be used as conductive anode electrolytic salt solution preparation of caustic soda. Graphite anode plate can be used as conductive anode in electroplating industry. It is an ideal material for electroplating. It can make electroplating products have the advantages of smoothness, delicacy, wear resistance, corrosion resistance, high brightness and not easy to change color.
Send your message to us
Low Resistance EDM Graphite Electrodes for Ferroalloy Plants
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 20mt m.t.
- Supply Capability:
- 20000MT/year m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches