Plastic Tubes HDPE Pipe CNBM Manufacturer ISO 4277 PE100 PE80

Ref Price:

Loading Port:: Tianjin

Payment Terms:: TT OR LC

Min Order Qty:: 100 m

Supply Capability:: 3000 m/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Specifications

1.Material: HDPE100
2.Color: Black or white with blue stripe
3.PN Grade:0.6-1.6MPa
4.Certification:ISO9001 CE

Feature:

1.Material:pe100

2.Standard:GB/T13663-2000

3.Certification:ISO9001:2008

4.Package:plastic filmed

5.Color:black with blue stripe or on request

6.SDR rating:SDR11 SDR13.6 SDR17 SDR21 SDR26

Applications:

1.Municipal water supply, gas supply and agriculture etc.

2.Commercial & Residential water supply

3.Industrial liquids transportation

4.Sewage treatment

5. Food and chemical industry

7. Replacement of cement pipes and steel pipes

8. Argillaceous silt, mud transportation

9. Garden green pipe networks

Advantage:

1.Non-toxic

2.Light Weight

3.No Leakage.

4.High Ductility.

5.Hygienic Safety

6.Toughness

7.Smooth Surface

8.Corrosion resistant.

9.Excellent Flexibility

10.Chemically Inert

11.Resistance to Abrasion

12.Good resistance ability for scratch.

13.Recycle and environment-friendly

14.Many new construction method,such as butt fusion and socket joint.

15.Easy Installation and Lower costs

16.Ageing resistance and long service life,50 years under pressure use

Properties :

1.Specific Gravity, g/cm3, 20(C): 0.941-0.965

2.Longitudinal Reversion, % (110(C)): <=3< span="">

3.Oxidation Induciton Time, min (200(C)): >=20

4.Extension Rate at Break. %: >=350

5.Hydraulic Pressure Test:

1)20(C), Hoop Stress is 12.4 Mpa, 100h: No Failure.

2)80(C), Hoop Stress is 5.5Mpa, 165h: No Failure.

3)80(C), Hoop Stress is 5.0Mpa, 1000h: No Failure.

Q: 1995 Honda Civic1.6L V-TECH Motor v4This is a good car there is only one problem the engine overheated and melted the plug wires. I replaced the Part but needs to have plug tubes cleaned out due to melted plastic. I need help from a mechanic expert about this as i do not have the tools to do the job but i could get them tools.: unless the melted plastic interferes with the new tubes or spark plugs, there is no reason to try to clean the plastic out. if you can get the plugs out and put new ones in and put the wires on with no problem then just leave the residue in there...it won't hurt anything. you are talking about a major undertaking if you want to remove the tubes to clean them. The valve cover has to come off to get to the tubes and the tubes are usually pressed into the base of the head so the head may have to come off as well. you might want to just pull the wires and try to use a rat-tail file down into the tube to scrape away the excess plastic on the inside of the tube (leave the spark plugs in place if you try this so the filings don't get into the engine). Then use a vacuum cleaner to suck the filings out of the tube before you put the wires back on. I'd recommend that as the best thing to do if the burnt plastic is a concern. Otherwise, I'd leave it alone. hope that helps

Q: The dishwasher behind my bar at work has a leak. The pipe that's leaking is Parker Parflex PP 3/8 plastic tubing that connects into a metal nut and brings clean water in. The pipe has a leak exactly where it meets the nut, so in theory I could cut off the cracked portion and then re-seal it to the nut. Can I cut it with wire cutters? Should it be sanded after I cut it? Do I use a teflon sealant? Thanks for any help!: That should be a compression fitting. If it's a brass fitting then they are one time use. You can get a new brass fitting, cut the PP tube clean with a knife or a razor blade - be careful not to cut yourself please, then install the nut over the tube, slip the compression ring over the tube and if there's an insert that goes inside the PP, insert that. Then push the hose into the fitting and slide the nut and ring to the threaded portion of the fitting and tighten it. Be careful to tighten it enough to seal but not so tight you cut through the pipe again. It's likely the reason you have the leak in the first place is because someone overtightened it. OR you can simply buy a replacement hose. I'd prefer a wire braid shielded pipe. Stronger and made with a professional fitting on the end, one you don't have to mess with. My opinion, replacing the tube is the better idea. And they're not stupidly expensive either. Good luck with your project. '')

Q: I know there are two kinds of plastic pipes: thermoplastic pipe and thermosetting plastic pipe. PPR what kind of plastic pipes do you have?: There was no poison, and the plasticizer was the problem. (heat can melt. It's thermoplastic, that is, plasticizers)

Q: My child left her pierced earrings on way too long. The plastic backs are hardened onto the post. They are not the flat round ones. These are small clear plastic tubes. There must be a softener of some kind, no? Please help.: this happened to me too, i had to pull VERY hard, it actually scared the hell out of me. all i did was wiggle it until it came out. no other way.

Q: Are plastic tubes suitable for use in the automotive industry?: Yes, plastic tubes are suitable for use in the automotive industry. They offer various advantages such as lightweight construction, resistance to corrosion, flexibility, and cost-effectiveness. Plastic tubes can be used for various applications in vehicles, including fuel lines, coolant systems, and air conditioning.

Q: What is the maximum temperature that plastic tubes can withstand?: The maximum temperature that plastic tubes can withstand can vary depending on the type of plastic used. However, most plastic tubes can generally withstand temperatures up to 150-200 degrees Celsius. It is important to consult the specific specifications of the plastic material being used for accurate temperature limits.

Q: Hot melt connection method of PE-RT plastic pipe and the matters needing attention: When welding elbow or three way, according to the design drawing requirements, should pay attention to the direction, in the pipe fittings and pipe in the straight direction, with auxiliary sign mark its position;

Q: Hehehe I love freeze pops. My favorite flavor is lime. :): I like them all !

Q: Is this okay?? I have him in a play area thing that has tubes and i looked over and he was asleep in them!! I kinda tapped on it to make sure he wasnt dead and he kinda woke up then went right back to sleep....: thats normal! I had two teddy bear hamsters, and they loved sleeping in those plastic tubes! I had those colorful plastic cages that had holes and places for tubes that led to other cages and sleeping nests and hamster wheels and such! Its completely normal(:

Q: How are plastic tubes filled with powders or granules?: Plastic tubes are typically filled with powders or granules using various methods such as gravity filling, volumetric filling, or vacuum filling. These processes involve carefully pouring or dispensing the powder or granules into the tube, ensuring proper measurement and control to achieve the desired fill level.

Send your message to us

*Email

*TEL

*Quantity

*Unit