Good Quality Steel Grinding Ball with High Hardness & Low Breakage & Good Wear-Resistance
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25M.T. m.t.
- Supply Capability:
- 150,000M.T. m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Good Quality Steel Grinding Ball with High Hardness & Low Breakage & Good Wear-Resistance
1) Regular Specifications for Steel Grinding Ball with High Hardness & Low Breakage & Good Wear-Resistance
Size: 15-150mm
Hardness: 55-65HRC
Breakage Rate<0.5%
Impact Toughness>12J/cm2
Endurance Test>10000times
2) Main Feature for Steel Grinding Ball with High Hardness & Low Breakage & Good Wear-Resistance
High Hardness
Low Breakage
Good Wear Resitance
Stable Chemical Composition
3) Chemical Composition for Steel Grinding Ball with High Hardness & Low Breakage & Good Wear-Resistance
Forged Grinding Ball:
Material | C | Mn | Si | Cr | S | P | V |
50MN | 0.48-0.56 | 0.70-1.0 | 0.17-0.37 | ≤0.25 | ≤0.035 | ≤0.035 | |
60MN | 0.57-0.65 | 0.70-1.0 | 0.17-0.37 | ≤0.25 | ≤0.030 | ≤0.030 | |
65MN | 0.60-0.70 | 0.90-1.20 | 0.17-0.37 | ≤0.25 | ≤0.030 | ≤0.030 | |
75Mn | 0.72-0.92 | 0.90-1.20 | 0.17-0.37 | ≤0.25 | ≤0.030 | ≤0.030 | |
75MnCr(B2) | 0.70-0.85 | 0.7-1.20 | 0.17-0.37 | 0.42-0.85 | ≤0.030 | ≤0.030 | |
75SiMn | 0.70-0.90 | 0.7-1.2 | 0.4-0.8 | ≤0.25 | ≤0.030 | ≤0.030 | |
Wear-resistant Alloy | 0.5-0.65 | 0.4-1.0 | 1.4-1.8 | 0.9-1.2 | ≤0.030 | ≤0.030 | 0.1-0.2 |
Casting Grinding Ball
Model | Material | C | Si | Mn | Cr | S | P |
High Chrome | Cr-22-32% | 2.0-2.8 | ≤1.0 | 0.5-2.0 | 22-32 | ≤0.01 | ≤0.01 |
Cr-17-22% | 2.0-2.8 | ≤1.0 | 0.5-2.0 | 17-22 | ≤0.01 | ≤0.01 | |
Cr-14-17% | 2.2-3.0 | ≤1.0 | 0.5-2.0 | 15-17 | ≤0.01 | ≤0.01 | |
Cr-10-14% | 2.2-3.2 | ≤1.0 | 0.5-2.5 | 11-14 | ≤0.01 | ≤0.01 | |
Medium Chrome | Cr-5-10% | 2.1-3.2 | ≤1.2 | 0.5-1.5 | 5-10 | ≤0.01 | ≤0.01 |
Low Chrome | Cr-1-5% | 2.2-3.5 | ≤1.2 | 0.5-1.5 | 1-5 | ≤0.02 | ≤0.02 |
4) Main Testing Methods for Steel Grinding Ball with High Hardness & Low Breakage & Good Wear-Resistance
Hardness Test:
Impact Toughness Test:
5) Packing Methods for Steel Grinding Ball with High Hardness & Low Breakage & Good Wear-Resistance
- Q:When there is no flaw detection for large casting parts, is there any crack inside?
- Cracks are considered serious levels of defects and should be repaired
- Q:What reason is the bronze statue choking fire?
- The casting process in boiling phenomenon, is the setting of the exhaust hole positioner position or number is not reasonable, the air cavity can not be discharged, overwhelmed by a material inlet, reflux, change mould, sincerely help you look forward to adopt,
- Q:What are the casting parts processing engineering?
- Among them, special casting has metal mould casting, pressure casting, low pressure casting, lost wax casting (also known as precision casting), shell casting, lost foam casting, centrifugal casting, continuous casting, V casting, and clay casting
- Q:What method of casting does not rust? I think the sample is like oil
- The surface of a general casting is easy to rust. In order to prolong the rusting period, antirust paint or antirust oil is usually sprayed. What you said should be anti rust oil.
- Q:Casting blank in the cooling process to release a large amount of heat energy, what can be recycled?
- Casting, do not need to provide a rough casting foundry drawings, according to your chart will put foot margin in the processing needs of the surface, the rest of the size can be found according to the mechanical design manual and manual casting. General Casting Factory Casting Division will be in your chart marked on shrinkage and processing margin figure (usually with red and green pen) to the patternmaker production of wood or other material mould diagram.
- Q:our factory now produces steel castings in the use of polishing directly after spraying processing, but the powder sprayed 15But the spray powder touched off what is the reason we are not very strict requirements not only need to peel off bubbles can also, because our products are steel castings so we use steam hole sludge put on. Do not know if this spray treatment has no effect to thank friends with us!
- Cast iron has not been done, if it is iron, then in the spray before going through strict pretreatment, the surface can not have a little oil dust
- Q:What are the casting parts used to test shrinkage holes?
- 3 fluorescent magnetic powder, this method can also be found in part.
- Q:What is the ejection angle of the die casting (Tan Gang)?
- Because after the wax, wax parts will have a slight contraction, which is good for demoulding. Many moulds don't do the ejection angleEspecially deep hole, and customers to discuss, generally take 0.3-1 degrees is enough
- Q:After reaming, the roughness can reach several levels, that is to say, the sample.Casting parts in rocker arm drilling, reaming, roughness, block. After reaming, the roughness can reach several levels, that is to say, the sample.
- Radial drilling machine can achieve boring, reaming function, but as much as you want, according to your requirements and material to determine!
- Q:Why does the surface of stainless steel casting mirror mirror ripple?
- Because the grinding machine is layer by layer. And the material inside the casting is not completely uniform.
1. Manufacturer Overview |
|
---|---|
Location | Zhangqiu, China |
Year Established | 1995 |
Annual Output Value | 150,000M.T. |
Main Markets | 40%,South America; 30%,South Africa; 15%,Southeast Asia; 5%, Europe Area; 5%, North America; 5%, Other Areas |
Company Certifications | ISO9001:2008;SGS Test Report |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Qingdao;Tianjin |
Export Percentage | |
No.of Employees in Trade Department | 25 |
Language Spoken: | English, Chinese |
b)Factory Information | |
Factory Size: | 68,000m2 |
No. of Production Lines | 15 |
Contract Manufacturing | |
Product Price Range | $700/M.T.-$1200/M.T. |
Send your message to us
Good Quality Steel Grinding Ball with High Hardness & Low Breakage & Good Wear-Resistance
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25M.T. m.t.
- Supply Capability:
- 150,000M.T. m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords