Fluoroplastic Lined Centrifugal Pump

Ref Price:

Loading Port:: Shanghai

Payment Terms:: TT or LC

Min Order Qty:: 1 set

Supply Capability:: 1000 Sets Per Month set/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Chemical Passage Pump

OH2 Heavy Duty Petrochemical Processing Pump

Slef-suction chemical centrifugal Pump

Ventical Condensate Pump

Double Suction Split Casing Pump

CDL Stainless Steel Vertical Multistage Centrifugal Pumps

AC Solar Water Submersible Centrifugal Pump

ISO Standard Horizontal Centrifugal End Suction Water Pump

This pump features superior corrosion resistance, high mechanical strenth, no aging and no toxin decomposing. They can be used to transport all kinds of acidic and alkaline liquid, oxidant and other corrosive media.

Q:How do I check if the oil pump is working properly?: Look at the oil pressure,

Q:What is the effect of excessive oil on the oil pump?: Hello, add too much oil will only cause the engine to produce carbon carbon, lead to excessive fuel consumption increase; to see you much to a lot of oil, if a little bit will not have much impact, if very much it has affected Oh, too much oil can lead to oil tank engine the inside of the car pressure increases, leading to the weakness and seals (such as all kinds of gaskets), and oil seal, oil burning etc. will lead to failure if can help you, please set the best answer, thank you!

Q:The car broke down and the maintenance crew thought it was a mechanical filter, but changed 4 machines, or did they leak oil?. Then he said it was caused by the high pressure of the oil pump. Replacement pump, heroes, help me. Is the pressure of the oil pump too high to cause oil leakage on the engine?: Such a problem can arise. The oil pressure is too high, and the oil filter is opened by "drum". The reason is that the oil pump pressure limiting valve [pressure relief valve], resulting in a failure, can not normally open at high pressure caused by pressure relief

Q:GY6 engine oil pump installation direction, there is an arrow pointing to the other side of the ah: The direction of the arrow indicates the direction of the oil, and the one with the arrow is connected to the engine oil inlet.

Q:Why is the Honda engine oil pump so big? What's the function of the other parts?: The balance shaft is the same as the oil pump, so it is larger.

Q:From where on the car can you see that the oil pump is not oiled?: Hello, not on the oil, then 1 valve sound than normal, 2, open the oil cap to see, 3, the best way is conditional removal of oil sensors, get off to see

Q:What is the influence of insufficient oil supply in the oil pump?: Tank or pipeline bubbles; hydraulic system from "Ji, Ji" sound to ascend; the tractor has just started working device can improve the elevated temperature after a period of work, ascension is slow or not to upgrade; light load can improve, can enhance the expansion stage heavy load.Failure cause:(1) hydraulic tank oil level is too low;(2) do not use hydraulic oil according to season;(3) the tubing is seriously blocked by dirt;(4) the gear oil seal of the oil pump is damaged, and the air enters the hydraulic system;(5) the oil pump inlet, outlet port or bent joint "O" shaped sealing ring is damaged. The fastening bolt of the bending joint or the inlet and outlet pipe nut are not tightened, and the air enters the hydraulic system;(6) the inner leakage of the oil pump and the aging of the sealing ring;(7) oil pump end face or main or driven gear sleeve end face wear or scratch, two axle sleeve end surface roughness is over bad;(8) internal assembly error of oil pump causes internal leakage;(9) "left hand" installed "right" oil pump, causing the impact of the skeleton oil seal;(10) hydraulic oil is dirty.

Q:4Y engine oil pump, okay? Still lifting the engine?: Hello, this oil pump is not very good, the replacement of the oil pan is not very good, it is more troublesome to dismantle.

Q:How long will the oil pump lubricate the engine parts after the engine is started?: According to my driving experience, it is better to warm up in 5-10 minutes after the cold weather, and start in hot weather for 1-2 minutes

Q:First question: I mean the turn key, the engine doesn't work, the seconds when the starter works. Does the oil pump inject oil into the engine during this time? Or wait until the engine is fully started to inject lubrication?The second question: because now the cold weather, I saw a forum of northeast riders turn the key to the starter operation recommendations for 1-2 seconds, then later normal launch, said that this can reduce engine wear, do this operation is correct?: Yes, the oil pump follows the crankshaft

Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview
Location	Hunan,China
Year Established	2006
Annual Output Value	US$5 Million - US$10 Million
Main Markets	59.00% Mid East 8.00% North America 8.00% Southern Europe 5.00% Eastern Asia 2.00% Africa 2.00% Oceania 2.00% Southeast Asia 2.00% Western Europe 2.00% South America 2.00% Central America 2.00% Northern Europe 2.00% Eastern Europe 2.00% South Asia 2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port	SHANGHAI,GUANGZHOU,DALIAN
Export Percentage	51% - 60%
No.of Employees in Trade Department	6-10 People
Language Spoken:	English, Chinese
b)Factory Information
Factory Size:	Above 100,000 square meters
No. of Production Lines	Above 10
Contract Manufacturing	OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range	High and/or Average